manualshive.com logo in svg

Parker AC30V Series, Technical Manual

Share
Download
Parker AC30V Series Technical Manual Download Page 13

 

 

 

 

Fan Control Application Manual   

11      

       

AC30V series Variable Speed Drive 

Fire Mode 

 Setup::Application::Fire Mode

 

 Monitor::Application::Fire Mode* 

 
Fire mode is intended for use in critical situations where it is imperative for the motor to be kept running if at all possible. In such a situation it may 
be reasonable to override the Drives’ normal protective functions. An example of a critical situation may be a ventilation fan in a stairwell, where 
continued operation in the event of a fire may assist the safe evacuation of personnel. 

 

Caution

 

When Fire Mode is active the Drive and Motor protection trips are disabled. The use of Fire Mode itself increases the risk of causing 
a fire by overloading the drive or motor, so it must only be used after assessing the risks. 

 

PNO 

Parameter Descriptions 

 

Fire Mode Activate 

Set TRUE to activate the Fire Mode feature. This input may only be set by connection to a digital input as part of the application. 

1961

 

Fire Mode Setpoint

 

A reference value to be used when Fire Mode is active. Setting a negative setpoint will cause the drive to rotate in reverse direction. 

1962

 

Fire Mode Level

 

This parameter selects the mode of operation when Fire Mode is activated. It is an enumerated value as follows: 
 

0  DISABLED 

Fire Mode feature is disabled. The 

Activate

 input going high will have no effect. 

1  PARTIAL 

Fire Mode is enabled with “partial mode” trips listed below ignored.  

2  FULL 

Fire Mode is enabled with “full mode” trips listed below ignored.  

 

1963

 

FM Restart Delay

 

This specifies the duration to wait before attempting to reset a trip. 

1964

 

Fire Mode Activated

 

When TRUE, this diagnostic, indicates that the Fire Mode is in operation. Trips are being ignored at either the PARTIAL or FULL level 
and the fire mode 

Setpoint, 

which is non-zero, is being followed. 

1965

 

Fire Mode Ready

 

This diagnostic, when TRUE, indicates that the Fire Mode will operate if the 

Activate 

input becomes

 

TRUE. The diagnostic will be 

FALSE if the fire mode 

Level

 is set to DISABLED or the fire mode 

Setpoint

 is set to 0.0%. 

www.comoso.com

Summary of Contents for AC30V Series































Reviews:

No comments

Brands by name

Popular brands

Load more brands