background image

25 

 

Supported DAC Sampling Rates 
       USB: 

up to

 

384

 

kHz / 32-bit PCM 

 

   DSD Native: DSD

 

64, DSD

 

128, DSD

 

256 

                DSD over PCM (DoP) at 384

 

kHz 

 

       Coax/Optical: 

up to

 

192

 

kHz / 24-bit PCM

 

 

Digital to Analog Converter  

       ESS Sabre

32

 Reference ES9018K2M 

       384

 

kHz / 32-bit 

       

 

USB 2.0 Controller 

       Savitech SA9227, 384

 

kHz / 32-bit

  

 

Headphone Amplifier 

       Texas Instruments TPA6120A 
        Output Impedance 10 ohms

  

 

XLR Pin Identification 

1 = Ground (Shield) 
2 = Positive 
3 = Negative (Return) 

 

Input Impedance  

Unbalanced: 24

 

k

 

Ω 

Balanced: 100

 

k Ω

 

per leg 

 

Preamplifer Output Impedance 

Unbalanced: 100

 

Ω 

Balanced: 470

 

Ω per leg 

 

Dimensions 

Width: 17-

1

/

4

” (437

 

mm) 

Depth: 16-

1

/

4

” (413

 

mm) 

Depth, with cables 17-

1

/

4

” (437

 

mm) 

Height, with feet: 5-

7

/

8

” (150

 

mm) 

Height, without feet: 5-

1

/

4

” (133

 

mm), 3U 

 

Net Weight  

33 lb. (15

 

kg) 

 

Shipping Weight 

45 lb. (20.4

 

kg) 

 

Power Requirement 

Standby: 0.5 watts 
Idling power: 70 watts 
Maximum: 750 watts 
110-125 VAC 60

 

Hz or 220-250 VAC 50

 

Hz 

       AC mains voltage is set on rear panel

 

 

Specifications 

 

Power Output - 

Both channels driven

 

(0.05% THD, 20

 

Hz - 20

 

kHz)

 

160 watts x 2 @ 8

 

Ω RMS 

240 watts x 2 @ 4

 

Ω RMS 

 

Power Output - 

Both channels driven

 

(0.9% THD, 20

 

Hz - 20

 

kHz)

 

180 watts x 2 @ 8

 

Ω RMS  

270 watts x 2 @ 4

 

Ω RMS 

 

Current Capacity 

45 amps peak per channel 

 

Frequency Response 

10

 

Hz - 100

 

kHz, +0/-3

 

dB 

20

 

Hz - 20

 

kHz, +0/-0.5

 

dB 

 

Total Harmonic Distortion (THD) 

< 0.01 %, average listening levels 
< 0.05 %, 160 watts x 2 @ 8

 

Ω 

 

Interchannel Crosstalk  

> 70

 

dB at 20

 

kHz 

> 78

 

dB at 1

 

kHz 

 

Signal to Noise Ratio - 

IHF A-weighted

 

Line in: - 103

 

dB (input shorted) 

Digital in: - 106

 

dB 

 

Amplifier Damping Factor 

      > 800 at 20

 

Hz  

 

Preamplifier Stage Input Sensitivity 

300

 

mV in for 1

 

V at Preamp Output jacks 

Total Preamp Stage Gain: 10

 

dB  

Max Output Unbalanced: 7

 

Max Output Balanced: 9

 

 

Power Amplifier Stage Sensitivity 

1

 

V at Bypass/Amp In for 28

 

V at Speaker Out 

Total Amp Stage Gain: 28

 

dB  

 

Phono Stage Sensitivity / Input Impedance 

MM: 41

 

dB / 47

 

k

 

Ω 

MC: 54

 

dB / 47

 

k

 

Ω or 100

 

Ω 

 

High & Low Pass Crossover Slope 

       12

 

dB per octave

 

 
 

Specifications and features subject to change or improvement without notice. 
Copyright Parasound Products Inc., 2018, Rev 1.0 

 

 

Summary of Contents for HINT 6



























Reviews: