background image

2

PLEASE REVIEW THE OWNER’S MANUAL AND INSTALLATION GUIDE IN 
ITS ENTIRETY AND HEED ALL SAFETY INFORMATION. Failure to follow these 
instructions and warnings can result in DEATH OR SERIOUS INJURY.

 

DANGER

DANGER indicates a hazardous situation which, 
if not avoided, will result in death or serious injury.

 

WARNING

WARNING indicates a hazardous situation which, 
if not avoided, could result in death or serious injury.

 

CAUTION

CAUTION indicates a hazardous situation which, 
if not avoided, could result in minor or moderate injury.

NOTICE

NOTICE is used to address practices not related to physical 
injury.

Signal Words and Symbols Used In This Manual 
This Owner’s Manual and Installation Guide contains specific precautions and symbols 
to identify safety-related information. You will find DANGER, CAUTION, WARNING 
and NOTICE symbols which require special attention. Please read them carefully and 
follow these precautions as indicated! They will explain how to avoid hazards that may 
endanger you or persons using or maintaining your pool or spa. 

SUCTION ENTRAPMENT HAZARD:

 

DANGER

DEATH or SERIOUS INJURY will result if a drain cover or grate 

is not installed and used correctly.
• Pool and spa pumps produce high levels of suction and move high 

volumes of water, which can cause death or serious injury if a person comes in close proximity to 

pool or spa drains.  

•  Keep clear of pool and spa drains to avoid death or serious injury from suction.

DEATH or SERIOUS INJURY will result from pool or spa drain covers or 

grates that are improperly installed, missing, clogged, or broken. 
• Inspect pool and spa before each use to ensure that drain covers and 

grates are properly in place and secured.  

•  Ensure that drain covers are not damaged, cracked, broken, loose, clogged, not properly secured, or 

missing because these conditions increase the chance of death or serious injury from entrapment.

•  If a drain cover is discovered damaged, cracked, broken, loose, clogged, not properly secured, or 

missing, you should:

  • Close the pool or spa immediately; and,
  •  Post a closure notice and keep the pool or spa closed until an appropriate ANSI/APSP -16-2011 

certified drain cover is properly installed.

DEATH or SERIOUS INJURY will result from hair entanglement or 

limb entrapment. 
•  Keep clear of pool and spa drains.
•  Hair sucked into pool or spa drains will tangle and knot trapping the 

swimmer underwater.  Avoid placing your hair near a pool or spa drain.

•  Avoid sitting on pool or spa drains because the suction can cause 

severe intestinal damage, evisceration, and/or disembowelment.

 

DANGER

 

DANGER

Summary of Contents for Paraskim V





















Reviews: