background image

6

• 

Never leave this machine unattended with the engine running. 

• 

Do not operate machine while under the influence of alcohol, drugs, or 
medication. 

• 

Never allow anyone to operate this machine without proper instruction. 

• 

Always operate this machine with all safety equipment in place and working.  
Make sure all controls are properly adjusted for safe operation. 

• 

Do not change the engine governor settings or overspeed the engine. The 
governor controls the maximum safe operating speed of the engine. 

• 

When loading a log, always place your hands on the sides of the log, not on 
the ends, and never use your foot to help stabilize a log. Not following these 
instructions may result in crushed or amputated fingers, toes, hand, or foot.    
                                           

• 

Use only your hand to operate the controls.

• 

Never attempt to split more than one log at a time unless the ram has fully 
extended and a second log is needed to complete the separation of the first log. 

• 

For logs which are not cut square, the least square end and the longest portion of 
the log should be placed toward the beam and wedge, and the square end placed 
toward the end plate. 

• 

When splitting in the vertical position, stabilize the log before moving the 
control. Split as follows:

 

a.  Place log on the end plate and turn until it leans against the beam and  

 

     is stable.

 

b.  When splitting extra large or uneven logs, the log must be stabilized with  

 

     wooden shims or split wood between the log and end plate or ground. 

• 

Always keep fingers away from any cracks that open in the log while splitting. 
They can quickly close and pinch or amputate your fingers. 

• 

Keep your work area clean. Immediately remove split wood around the machine 
so you do not stumble over it. 

• 

Never move this machine while the engine is running. 

• 

This machine should not be towed on any street, highway or public road. 

• 

Do not tow machine faster than 45kph on smooth ground. 

 

   

 

LOG SPLITTER

Summary of Contents for LS42I




























Reviews: