background image

2

 October 

2004

MIM2-A2-GZ40-00

sublicense) to use the Software, solely as it is intended and solely as incorporated 
in the Product purchased from Paradyne or its authorized distributor or reseller 
under the following terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors. 

The Licensee acquires no title, right or interest in the Software other than the 
license granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in 

which the Product was rightfully purchased except upon prior written notice to 
Paradyne and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the 

Software in whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is 

provided “AS IS” and in its present state and condition and Paradyne makes 
no other warranty whatsoever with respect to the Product purchased by you. 
THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES, 
WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING 
WITHOUT LIMITATION:

a.

Any warranty that the Software is error-free, will operate uninterrupted in 
your operating environment, or is compatible with any equipment or 
software configurations; and

b.

ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT 
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS 
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied 
warranties on limitations on how long an implied warranty lasts, so the above 
limitations may not apply to you. This warranty gives you specific legal rights, 
and you may also have other rights which vary from one state or jurisdiction to 
another.

6. In no event will Paradyne be liable to Licensee for any consequential, 

incidental, punitive or special damages, including any lost profits or lost 
savings, loss of business information or business interruption or other 
pecuniary loss arising out of the use or inability to use the Software, whether 
based on contract, tort, warranty or other legal or equitable grounds, even if 
Paradyne has been advised of the possibility of such damages, or for any 
claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or 

otherwise transferred by the Licensee to any third party without the prior 
written consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be 

terminated in the event of breach by the Licensee of any provisions of this 
Agreement. 

9. Upon such termination, the Licensee shall refrain from any further use of the 

Software and destroy the original and all copies of the Software in the 
possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without 

regard to its provisions concerning conflicts of laws.

Summary of Contents for MIM-2E1









Reviews: