manualshive.com logo in svg

Paradyne Hotwire 8300, User Manual

Share
Download
Paradyne Hotwire 8300 User Manual Download Page 89

2. Web Server Interface

8300-A2-GB20-00

April 2003

2-71

IP Address

Original IP Address of the host. 

NAT IP Address

Translated IP Address of the host. 

Processed Packets

Number of packets processed by NAT for this address.

Dynamic Host Configuration Protocol (DHCP)

DHCP provides a mechanism through which computers using TCP/IP can obtain 
protocol configuration parameters automatically through the network.

The most important configuration parameter associated with DHCP is the IP 
Address. A computer must initially be assigned a specific IP Address that is 
appropriate to the network to which the computer is attached, and that is not 
assigned to any other computer on that network. If a computer moves to a new 
network, it must be assigned a new IP Address for that new network. DHCP can 
be used to manage these assignments automatically.

DHCP has other important configuration parameters also, such as the subnet 
mask, default router, and Domain Name System (DNS) server. Using DHCP, a 
network administrator can avoid hands-on configuration of individual computers 
through complex and confusing setup applications. Instead, those computers can 
obtain all required configuration parameters automatically, without manual 
intervention, from a centrally managed DHCP server. DHCP is available on the 
10/100 Ethernet port only.

NOTICE: 

You must Save and Restart for any changes in DHCP configuration 
parameters to take effect. 

DHCP Server Details Screen

The DHCP Server Details screen (

Figure 2-64

) lets you configure the parameters 

described below.

Figure 2-64. DHCP Server Details Screen

Enable

Enables or disables the DHCP Server. Default is Enable.

Summary of Contents for Hotwire 8300











































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands