background image

 20

CAUTION:

Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as
appropriate.

The Ringer Equivalence Number (REN) assigned to each terminal device provides an
indication of the maximum number of terminals allowed to be connected to a telephone
interface. The termination on an interface may consist of any combination of devices
subject only to the requirement that the sum of the Ringer Equivalence Numbers of all
the devices does not exceed 5.

If your equipment is in need of repair, refer to 

Warranty, Sales, Service, and Training

Information.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor directly for
any help needed. For additional information concerning warranty, sales, service, repair,
installation, documentation, training, distributor locations, or Paradyne worldwide office
locations, use one of the following methods:

H

Internet:  Visit the Paradyne World Wide Web site at www.paradyne.com
(Be sure to register your warranty at www.paradyne.com/warranty.)

H

Telephone:  Call our automated system to receive current information by fax or to
speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

Document Feedback

We welcome your comments and suggestions about this document. Please mail them
to Technical Publications, Paradyne Corporation, 8545 126th Ave. N., Largo, FL 33773,
or send e-mail to [email protected]. Include the number and title of this
document in your correspondence. Please include your name and phone number if you
are willing to provide additional clarification.

Trademarks

Hotwire is a registered trademark of Paradyne Corporation. All other products and
services mentioned herein are the trademarks, service marks, registered trademarks or
registered service marks of their respective owners.

 

*5216–A2–GN10–30*

Copyright 

E

 2000 Paradyne Corporation. Printed in U.S.A.

Summary of Contents for Hotwire 5216





















Reviews: