background image

3

Refer to 

About FrameSaver DSL Devices in the User’s Guide for a list of FrameSaver 

DSL 9783 features, and the capabilities provided by each feature set.

Upgrading a Basic Unit to SLV

A basic FrameSaver DSL 9783 Router can be upgraded to full SLV capability at any time 
by ordering a FrameSaver SLV Activation Certificate. A certificate can be ordered for a 
single 9783 router, or for many 9783 routers. The OpenLane

®

 SLM system, Release 5.3 

or later, is required to schedule the activation of SLV features, and to manage the 
certificate activations included in the certificate.

To upgrade a basic 9783 router to full SLV capability, order the FrameSaver SLV 
Activation Certificate (Feature No. 9783-C1-220), providing the model to be activated 
(i.e., 9783-Rtr), your OpenLane SLM system license key number, the number of 9783 
router activations to be included on the certificate.

To learn more about activating SLV capability, refer to the 

FrameSaver SLV Activation 

Instructions (Document No. 9000-A2-GK43), or contact your sales representative.

Product Documentation Online

Complete documentation for this product is available at www.paradyne.com
Select 

Library 

 Technical Manuals 

 FrameSaver Frame Relay Devices.

Select the following document:

9783-A2-GB20
FrameSaver DSL 9783 User’s Guide

To order a paper copy of a Paradyne document:

„

Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)

„

Outside the U.S.A., call 1-727-530-8623

Package Checklist

In addition to these instructions, verify that your package contains the following:

FrameSaver DSL 9783 Router

Power cord with power transformer

Tie wrap for power cord strain relief

DSL network access cable with 8-pin connectors – U.S. models only

Ferrite choke – International models only

FrameSaver DSL 9783 Router Quick Reference (Document No. 9783-A2-GL11)

Be sure to register your warranty at www.paradyne.com/warranty.

Summary of Contents for FrameSaver 9783





























Reviews: