background image

2

November 1996

3980-A2-GZ41-10

exceed five (5.0). To be certain of the number of
devices that may be connected to the line, as
determined by the total RENs, contact the
telephone company to determine the maximum
RENs for the calling area.

4. If the 3811Plus modem causes harm to the

telephone network, the telephone company will
notify you in advance that temporary
discontinuance of service may be required. But if
advance notice is not practical, the telephone
company will notify the customer as soon as
possible. Also, you will be advised of your right to
file a complaint with the FCC if you believe it is
necessary.

5. The telephone company may make changes in its

facilities, equipment, operations, or procedures
that could affect the operation of the equipment. If
this happens, the telephone company will provide
advance notice in order for you to make the
necessary modifications in order to maintain
uninterrupted service.

6. If you require technical assistance or repair, see

Equipment Support and Warranty on page 4.

If the trouble is causing harm to the telephone
network, the telephone company may request that
you remove the equipment from the network until
the problem is resolved.

7. The user is not authorized to repair or modify the

equipment.

8. This equipment cannot be used on public coin

service provided by the telephone company.
Connection to Party Line Service is subject to
state tariffs. (Contact the state public utility
commission, public service commission, or
corporation commission for information.)

9. The Telephone Consumer Protection Act of 1991

makes it unlawful for any person to use a
computer or other electronic device to send any
message via a telephone fax machine unless such a
message clearly contains, in a margin at the top or
bottom of each transmitted page, or on the first
page of the transmission, the date and time it is
sent, and an identification of the business, or other
entity, or other individual sending the message,
and the telephone number of such business, or
other entity, or individual.

In order to program this information, follow the
steps outlined in the manual supplied with your
fax software.

Notice to Users of the Canadian Public
Switched Telephone Network

The Canadian Department of Communications label

identifies certified equipment. This certification means
that the equipment meets certain telecommunications
network protective, operational, and safety requirements.
The Department does not guarantee the equipment will
operate to the user’s satisfaction.

Before installing this equipment, users should ensure

that it is permissible to be connected to the facilities of the
local telecommunications company. The equipment must
also be installed using an acceptable method of
connection. In some cases, the company’s inside wiring
associated with a single line individual service may be
extended by means of a certified connector assembly
(telephone extension cord). The customer should be aware
that compliance with the above conditions may not
prevent degradation of service in some situations.

Repairs to certified equipment should be made by an

authorized Canadian maintenance facility designated by
the supplier. Any repairs or alterations made by the user to
this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to
disconnect the equipment.

Users should ensure for their own protection that the

electrical ground connections of the power utility,
telephone line and internal metallic water pipe system, if
present, are connected together. This precaution may be
particularly important in rural areas.

CAUTION

Users should not attempt to
make such connections
themselves, but should
contact the appropriate
electric inspection authority,
or electrician, as appropriate.

Summary of Contents for COMSPHERE 3811Plus














Reviews: