background image

BSX8-A2-GZ40-10

March 2005

15

Regulatory Compliance for Class A Equipment

The following regulatory compliance information applies to a BSX8000-5 as 
installed in a Paradyne BLC.

US Federal Communications Commission (FCC)

NOTE: This equipment has been tested and found to comply with the limits for a 
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference when the 
equipment is operated in a commercial environment. This equipment generates, 
uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to 
cause harmful interference in which case the user will be required to correct the 
interference at his own expense.

Caution: Changes or modifications not expressly approved by the manufacturer 
could void the user's authority to operate the equipment.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003. 

Cet appareil numérique de la Classe A est conforme à la norme NMB-003 du 
Canada. 

Europe

This Class A product complies with European Norm EN55022. 

Warning: In a domestic environment this product may cause radio interference in 
which case the user may be required to take adequate measures to correct the 
situation. 

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor 
directly for any help needed. For additional information concerning warranty, sales, 
service, repair, installation, documentation, training, distributor locations, or 
Paradyne worldwide office locations, use one of the following methods:

„

Internet:

 Visit the Paradyne World Wide Web site at 

www.paradyne.com

(Be sure to register your warranty at 

www.paradyne.com/warranty

.)

„

Telephone:

 Call our automated system to receive current information by fax or 

to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340       

Copyright 2005 Paradyne Corporation. Printed in U.S.A.

Summary of Contents for BSX8000-5

















Reviews: