background image

8400-A2-GZ40-10

October 2003

17

 Important Safety Instructions

The OC3 configuration of the SCP circuit card has provisions for the customer to 
install Class 1 laser transceivers to provide optical coupling to the 
telecommunications network. Once a Class 1 laser is installed, the equipment is 
considered to be a Class 1 laser product (Appareil à Laser de Classe 1). If  the 
Class 1 laser device is not purchased from Paradyne Corp., the customer is 
responsible to insure that the Class 1 AEL (Allowable Emissions Limit) per EN/IEC 
60825 is not exceeded after the laser transceivers have been installed. Do not  
install laser products whose class rating is greater than 1. Refer to the important 
safety instructions that accompany the transceiver prior to installation. Only laser 
Class 1 devices certified for use in the country of installation by the cognizant 
agency are to be utilized with this product. Also, laser warnings are to be provided 
in accordance with IEC 60825-1 and its Amendments 1 and 2, as well as 21 CFR 
1010 and 1040.10(g).

OC3 Uplink Specifications

Number of ports

Connector Type

Standards Supported

Frame Formats

Line Type

Data Rates Supported

Facility Datalink Protocol

Cable Distance

Model 8412 (MMF)
Model 8413 (SMFIR)
Model 8414 (SMFLR)

1 OC3

Duplex LC Socket

ANSI T1.105.06-94 Jitter, ANSI T1.105.09 94 Jitter, 
ANSI T1.117.06-91, ITU-T G.957 7/95

OC3 or STM-1 Operation, Direct Mode only

Non-Return to Zero

155.52 Mbps

ANSI T1.105 Format, ANSI T1.646 HEC, ITU-T I.432 
Scrambler

2 Km (6561.7 feet)
15 Km (49,212.6 feet) SMF fiber
40 Km (131,234 feet) SMF fiber

IMA Uplink Specifications

Number of ports

Connector Type

Standards Supported

Frame Formats

Line Type

Data Rates Supported

Facility Datalink Protocol

Cable Distance

8 T1 or E1

RJ45M-type (50-pin telco)

RFC 495, ANSI T1.403, ITU G.703/G.704

T1: Superframe, extended Superframe
E1: E1, E1-CRC

T1: B8ZS
E1: HDB3

T1: 1.544 Mbps per T1 (max. 8 T1)
E1: 2.048 Mbps per E1 (max. 8 E1)

ANSI T1.403

T1/E1 (short haul): 200 meters (656 feet) (LBO=0, –7, –15, 
–22 dB)
T1/E1 (long haul): 2000 meters (6561.7 feet)

Table 5. SCP Card Technical Specifications (2 of 2)

Specifications

Criteria

Summary of Contents for 8411-A1-000



















Reviews: