background image

8400-A2-GZ40-10

October 2003

15

Equipment List

The following feature numbers may be used to order SCP cards, line cards, and 
related cables.

Table 4. Feature Numbers

Description

Feature Number

Cards

SCP Card: DS3

8411-A1-000

SCP Card: OC3/STM1 Multimode Fiber

8412-A1-000

SCP Card: OC3/STM1 Single Mode Fiber Intermediate Reach

8413-A1-000

SCP Card: OC3/STM1 Single Mode Fiber Long Reach 

8414-A1-000

SCP Card: 8-Port DS1 IMA 

8416-A1-000

SCP Card: 8-Port E1 IMA

8417-A1-000

MCP GranDSLAM 3.0

8900-B1-211 

ADSL2 ATM Line Card 24 ports Annex A

8965-B1-000 

ReachDSL 2.2 ATM Line Card 24 ports

8955-B1-000 

G.SHDSL ATM Line Card 24 ports 

8985-B1-000 

Cables

LC-to-SC Conversion Cable for SCP Multi-Mode Fiber

8400-F1-001

LC-to-SC Conversion Cable for SCP Single Mode Fiber

8400-F1-002

Y-Cable for SCP Redundancy: 
LC Connections, Multi-Mode Fiber

8400-F1-003

Y-Cable for SCP Redundancy: 
LC connections, Single Mode Fiber

8400-F1-004

Y-Cable for SCP Redundancy: 
SC Connections, Multi-Mode Fiber

8400-F1-005 

Y-Cable for SCP Redundancy: 
SC Connections, Single Mode Fiber

8400-F1-006 

Y-Cable for SCP Redundancy: 
DS3

8400-F1-007 

50-Position Connector to Eight 8-Pin Modular Jacks Cable

8026-F1-001 

50-Position Connector to Sixteen BNC Jacks Cable

8027-F1-001

Summary of Contents for 8411-A1-000



















Reviews: