Paradox Magellan MG5050E, Installation Manual

Page: 26 / 68

26
Magellan & Spectra SP • Installation Guide
Access Codes
The control panel supports the following access codes:
Access Code Length
Section [701] : System Options
Option [1] OFF= 6-Digit Access Codes (valid code entries include 000000 to 999999)
Option [1] ON= 4-Digit Access Codes (default) (valid code entries include 0000 to 9999)
All access codes can be set to lengths of either 4- or 6-digits. When the 4-digit option is selected, entering a 4-digit code will allow access. Using the 6-digit option,
entering 6 digits is required to allow access.
WARNING: If the access code length is changed from four digits to six digits when access codes have already been programmed, the control panel
will automatically add the last 2 digits by using the first 2 digits. For example, if the access code is 1234 and you switch to 6 digits, the code will
become 123412. Be sure to verify the access codes after switching from 4-digit access codes to 6-digit codes. When switching from six digits to four
digits, the control panel will simply remove the final two digits of the access code. For example, 123456 will become 1234.
Installer Code (Default: 0000 / 000000)
The Installer Code is used to enter the system‘s programming mode, which allows you to program all the features, options and commands of the control panel. The
Installer Code can be 4- or 6-digits in length (See “Access Code Length” on page 26) where each digit can be any value from 0 to 9. The Installer Code cannot be used
to program Master Code 1, Master Code 2 or user access codes. To program the Installer Code press:
[
ENTER
]
+
[
CURRENT INSTALLER CODE
]
+ [397] + new 4- or 6-digit Installer Code
Maintenance Code (Default: Empty)
The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to program all the features, options and
commands
except for the system’s communication settings (sections [395] , [397] , [398] , [815] , [816] , [817] , [910] , and [911] ) as well as any user codes. The
Maintenance code can be 4 or 6 digits in length where each digit can be any value from 0 to 9. The Maintenance code is empty by default. Set the Maintenance in
section
[398] .
[
ENTER
]
+
[
INSTALLER CODE
]
+ [398] + new 4- or 6-digit Maintenance Code
System Master Code (Default: 1234 / 123456)
The Installer Code can be used to program the System Master Code. With the System Master Code a user can use any arming method and can program any user access
code, but not the User Code Options. The System Master Code can be 4 or 6 digits in length, where each digit can be any digit from 0 to 9. The System Master Code can
be modified but cannot be erased. To change the System Master Code press:
[
ENTER
]
+
[
INSTALLER CODE
]
+ [399] + new 4- or 6-digit System Master Code
User Code Options
Sections [404] to [432] : Options [1] to [8]
The User Code Options define which arming methods each user can use to arm or disarm the system. Regardless of these settings, all users can Regular arm
assigned partitions and all users except those with the Arm Only option can disarm an assigned partition, regardless of how it is armed. Select one or more of the
options described on the following pages for each user access code, where sections
[404] to [432] represent user access codes 004 to 032.
Partition 1 Assignment
Sections [404] to [432] : User codes 004 to 032
Option [1] OFF= Deny access to partition 1
Option [1] ON= User code has access to partition 1 (default)
If the system is partitioned (See “Partitioning” on page 58), user codes with this option enabled can arm and disarm partition 1.
WARNING: If the system is not partitioned, you must assign partition 1 to the user access code. Otherwise, the user access code will be considered
disabled.
Installer Code [397] : Used to program all control panel settings except user access codes.
Maintenance Code [398] :
The Maintenance code is similar to the Installer code. It can be used to enter programming mode, which allows you to pro-
gram all the features, options and commands
except for the panel’s communication settings. The maintenance code is
empty by default.
System Master Code [399] :
Provides full access. Arm and disarm using any method described in the
User Code Options
below as well as program the
user access codes.
Master Code 1:
Permanently assigned to partition 1. Same as a regular user code except it can also program access codes for user codes
assigned to partition 1.
Master Code 2:
Permanently assigned to partition 2. Same as a regular user code except it can program access codes for user codes
assigned to partition 2. If the system is not partitioned Master Code 2 will be assigned to partition 1.
29 User Codes: Can arm and disarm as per User Code Options on page 26.