background image

FCC WARNINGS

EESSP

PR

RIITT

738EXPRESS / 

EESSP

PR

RIITT

738

IMPORTANT INFORMATION

This equipment complies with Part 68 of the FCC rules. Inside the cover of this equipment is a label that contains, among other
information, the FCC registration number of this equipment.

NOTIFICATION TO TELEPHONE COMPANY

Upon request, customer shall notify telephone company of particular line to which the connection will be made, and provide the
FCC registration number and the ringer equivalence of the protective circuit.

FCC 

REGISTRATION NUMBER

:

5A7CAN-22633 - AL - E

RINGER EQUIVALENCE NUMBER

:

0.1B

USOC 

JACK

:

RJ31X (USA), CA31A (CANADA)

TELEPHONE CONNECTION REQUIREMENTS

Except for telephone company-provided ringers, all connections to the telephone network shall be made through standard plugs and telephone
company-provided jacks, or equivalent, in such a manner as to allow for easy, immediate disconnection of terminal equipment. Standard jacks
shall be so arranged that, if plug connected thereto is withdrawn, no interference to operation of equipment at customer's premises which
remains connected to telephone network shall occur by reason of such withdrawal.

INCIDENCE OF HARM

Should terminal equipment/protective circuitry cause harm to telephone network, telephone company shall, where practicable, noti-
fy customer that temporary disconnection of service may be required; however, where prior notice is not practicable, the telephone
company may temporarily discontinue service if action is deemed reasonable in circumstances. In case of temporary discontinu-
ance, telephone company shall promptly notify customer and will be given opportunity to correct the situation.

CHANGES IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES

The telephone company may make changes in its communication facilities, equipment operations or procedures, where such
actions are reasonably required and proper in its business. Should any such changes render customer's terminal equipment incom-
patible with the telephone company facilities, the customer shall be given adequate notice to effect the modifications to maintain
uninterrupted service.

GENERAL

This equipment shall not be used on coin telephone lines. Connection to party line service is subject to state tariffs.

RINGER EQUIVALENCE NUMBER

(

REN

)

The 

REN

is useful to determine the quantity of devices that you may connect to your telephone line and still have all of those devices

ring when your telephone number is called. In most, but not all areas, sum of the 

REN

's of all devices connected to one line should

not exceed five (5.0). To be certain of the number of devices that you may connect to your line, you may want to contact your local
telephone company.

EQUIPMENT MAINTENANCE FACILITY

If you experience trouble with this telephone equipment, please contact facility indicated below for information on obtaining service
or repairs. The telephone company may ask that you disconnect this equipment from network until problem is corrected or until you
are sure that the equipment is not malfunctioning.

U

.

S

POINT OF CONTACT

:

Wackenhut International Inc.
10446 N.W. 31 terrace
Miami, Florida
33172 USA  1-305-994-8167

FCC PART

15, 

WARNINGS

INFORMATION TO USER

This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to equipment intermittently, the user is encouraged to try to correct the interference by one or more of the following
measures: (1) reorient or relocate the receiving antenna; (2) increase the separation between the equipment and receiver; (3) con-
nect the equipment to an outlet on a circuit other than the one to which the receiver is connected, or (4) consult the dealer or an
experienced radio/tv technician for assistance.

CAUTION

Changes or modifications not expressly approved by PARADOX SECURITY SYSTEMS could void the user's authority to
operate the equipment.

32

IM738-738EX

Summary of Contents for Esprit 738





































Reviews: