Paradox Esprit 738 EXPRESS Installation Manual Download Page 36

Page: 36 / 36

24 hour - fire/regular . . . . . . . . . . . . . . . . . . . . . 22

3 digit decimal value programming . . . . . . . . 15

About paradox . . . . . . . . . . . . . . . . . . . . . . . . . 4

About this manual . . . . . . . . . . . . . . . . . . . . . . 4

AC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Accessory modules . . . . . . . . . . . . . . . . . . . . . 6

Advanced technology zoning (ATZ) . . . . . . . . 5, 9, 21

Alarm memory . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Alarm relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Always report disarm . . . . . . . . . . . . . . . . . . . . 20

Arming codes/disarming codes . . . . . . . . . . . . 23

Arming/disarming . . . . . . . . . . . . . . . . . . . . . . . 20-21, 25-26

Associated zone deactivation . . . . . . . . . . . . . 21

Audible trouble warning . . . . . . . . . . . . . . . . . 21

Auto arm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16, 18, 21

Auto zone shutdown . . . . . . . . . . . . . . . . . . . . . 19

Automatic event buffer transmission . . . . . . . 19-20

Auxiliary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 28

Basic installation . . . . . . . . . . . . . . . . . . . . . . . . 6-11

Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 28

Beep on exit delay . . . . . . . . . . . . . . . . . . . . . . . 20

Bell/siren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7, 16, 19, 28

Bypass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22, 27

Call back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Chime zones . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Code priority . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Communicator formats . . . . . . . . . . . . . . . . . . 13-14

Communicator report failure . . . . . . . . . . . . . . 28

Current consumption . . . . . . . . . . . . . . . . . . . . 6

Dialing pulse rates . . . . . . . . . . . . . . . . . . . . . . 18

Digital communicator . . . . . . . . . . . . . . . . . . . . 6

Double stay arming . . . . . . . . . . . . . . . . . . . . . . 24

Duress alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Earth ground . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Entry delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 22

Espload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5, 6, 11

Event buffer and real time clock . . . . . . . . . . . 5

Exit delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

False alarm prevention . . . . . . . . . . . . . . . . . . . 4

Fast exit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Fast regular arming . . . . . . . . . . . . . . . . . . . . . 25

Fast stay arming . . . . . . . . . . . . . . . . . . . . . . . . 25

FCC compliance . . . . . . . . . . . . . . . . . . . . . . . . 32

Feature select programming . . . . . . . . . . . . . . 17

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Fire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 28

Follow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Force (away) arming . . . . . . . . . . . . . . . . . . . . . 24

Hexa programming . . . . . . . . . . . . . . . . . . . . . . 11

High-speed preprogrammed communication 4

Industry Canada . . . . . . . . . . . . . . . . . . . . . . . . 33

Inputs and outputs . . . . . . . . . . . . . . . . . . . . . . 5

Installer code . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Installer lock . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Installer programming . . . . . . . . . . . . . . . . . . . 11-24

Instant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Intellizone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 22

Key access programming . . . . . . . . . . . . . . . . 29

Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6, 8, 11

Keypad zone supervision . . . . . . . . . . . . . . . . . 21

Keyswitch / PS1 . . . . . . . . . . . . . . . . . . . . . . . . . 18, 27

Late to close . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Location and mounting . . . . . . . . . . . . . . . . . . . 6

Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

No movement . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 16

Operating modes . . . . . . . . . . . . . . . . . . . . . . . . 5

Panel answer options . . . . . . . . . . . . . . . . . . . . 12

Panel identifier . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Panel programming methods . . . . . . . . . . . . . . 11

Panic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20, 27

Partitioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4, 18, 25-27

PC password . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Power failure . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 20, 28

Power-down reset . . . . . . . . . . . . . . . . . . . . . . . 29

Powering-up the unit . . . . . . . . . . . . . . . . . . . . . 11

Programmable delay before alarm transmission 17

Programmable features . . . . . . . . . . . . . . . . . . . 11

Programmable output (PGM) . . . . . . . . . . . . . . 5, 7, 14-15, 17

Programming info . . . . . . . . . . . . . . . . . . . . . . . 30-31

Programming master and user codes . . . . . . . 28

Recent closing delay . . . . . . . . . . . . . . . . . . . . . 17

Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Reporting codes . . . . . . . . . . . . . . . . . . . . . . . . 22-24

Reporting options . . . . . . . . . . . . . . . . . . . . . . . 18-19

Requirements(UL, ULC and Austel) . . . . . . . . .

Shutdown codes . . . . . . . . . . . . . . . . . . . . . . . . 23

Silent/audible . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 22

Single zone connections . . . . . . . . . . . . . . . . . 8-9

Special codes . . . . . . . . . . . . . . . . . . . . . . . . . . . 23-24

Special timing functions . . . . . . . . . . . . . . . . . . 15-17

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6

Stay arming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Streamlined section programming . . . . . . . . . 12

System account codes . . . . . . . . . . . . . . . . . . . 13

System assignment . . . . . . . . . . . . . . . . . . . . . . 22

System options . . . . . . . . . . . . . . . . . . . . . . . . . 17-21

Tamper bypass . . . . . . . . . . . . . . . . . . . . . . . . . 21

Tamper/wire fault . . . . . . . . . . . . . . . . . . . . . . . . 10, 20, 28

Telephone and account numbers . . . . . . . . . . 12-13

Telephone line . . . . . . . . . . . . . . . . . . . . . . . . . . 10, 17, 28

Time correction . . . . . . . . . . . . . . . . . . . . . . . . . 13

Timer loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Total compatibility . . . . . . . . . . . . . . . . . . . . . . . 4

Touch tone options . . . . . . . . . . . . . . . . . . . . . . 18

Trouble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23, 27, 28

User-friendly operation . . . . . . . . . . . . . . . . . . . 4

User/access code length . . . . . . . . . . . . . . . . . 20

User/keypad functions . . . . . . . . . . . . . . . . . . . 24-29

Warranty statement . . . . . . . . . . . . . . . . . . . . . . 29

Zone alarm codes . . . . . . . . . . . . . . . . . . . . . . . 23

Zone definition . . . . . . . . . . . . . . . . . . . . . . . . . . 21-22

Zone input terminals . . . . . . . . . . . . . . . . . . . . . 8

Zone restore codes . . . . . . . . . . . . . . . . . . . . . . 23

Zone restore transmission . . . . . . . . . . . . . . . . 20

Zone speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Zones with EOL resistors . . . . . . . . . . . . . . . . . 20

IM738-738EX

Summary of Contents for Esprit 738 EXPRESS





































Search results

Summary of Contents for Esprit 738 EXPRESS

Reviews:

Related manuals for Esprit 738 EXPRESS

Brands by name

Popular brands

Paradox Esprit 738 EXPRESS, Installation Manual

Search results

Summary of Contents for Esprit 738 EXPRESS

Reviews:

Related manuals for Esprit 738 EXPRESS

Brands by name

Popular brands