ParaBody GS4 User Manual Download

Page: 18 / 27

STEP 17:

FIGURE 17

• Route the LAT CABLE (AM) around one

4-1/2” PULLEY

(36) and assemble the PULLEY to the LEFT (D) and RIGHT (E) BOOM

PLATES using one 3/8 X 3-3/4” BOLT (6), one LONG “L” CABLE BRACE (S), one 1” SPACER (24) and one 3/8” LOCK NUT (19).
See FIGURE 17.

• Route the LAT CABLE (AM) around one 3-1/2” PULLEY (35) and assemble two FLOATING PULLEY PLATES (AB) to the 3-1/2” PULLEY

(35) using one 3/8 X 1-3/4” BOLT (11) and one 3/8” LOCK NUT (19). See FIGURE 17.

(NOTE: Make sure the cable runs in the grooves

of the pulleys.)

•

SECURELY

assemble two PLASTIC SLEEVES (34) to the LEFT (D) and RIGHT (E) BOOM PLATES using two 3/8 X 3-3/4” BOLTS (6)

and two 3/8” LOCK NUTS (19) as shown in FIGURE17.

• Route the LAT CABLE (AM) over two 3-1/2” PULLEYS (35) and assemble the PULLEYS to the LEFT (D) and RIGHT (E) BOOM

PLATES using two 3/8 X 3-3/4” BOLTS (6), two SHORT “L” CABLE BRACES (R), two 15/16” SPACERS (24) and two3/8” LOCK
NUTS (19). See FIGURE 17.

• Screw the threaded end of the LAT CABLE (AM) into the end of the HEAD PLATE ASSEMBLY (AF) .See FIGURE 17.

3/8 X 3-3/4” 6

11 3/8 X 1-3/4”

4-1/2” PULLEY

Summary of Contents for GS4




























Search results

Summary of Contents for GS4

Reviews:

Related manuals for GS4

Brands by name

Popular brands

ParaBody GS4, User Manual

Search results

Summary of Contents for GS4

Reviews:

Related manuals for GS4

Brands by name

Popular brands