manualshive.com logo in svg

ParaBody 425103, Assembly Instructions Manual

Share
Download
ParaBody 425103 Assembly Instructions Manual Download Page 11

11

    FIGURE 11

STEP 11

•   Insert two GUIDE RODS (36) into the BASE (1) as shown on FIGURE 11. 

(NOTE:  Lubricate GUIDE RODS (36) with

silicon or teflon spray available at most hardware stores.)

•   Slide two 1-1/4 SQ. X 4-7/8” TUBES (34), two 3/4” WASHERS (71), and two WEIGHT STACK CUSHIONS (70) - 

IN THAT

ORDER  - 

down over the GUIDE RODS (36).

•   

SECURELY

 assemble the SELECTOR SHAFT (73) to the HEAD PLATE (72) using one 3/8 X 1-1/4” BOLT (83) and one 3/8”

WASHER (91).

•   Using

 EXTREME CARE 

slide all fifteen WEIGHT PLATES (105) down over the GUIDE RODS (36) on to the WEIGHT STACK

CUSHIONS (70). Make sure that the keyholes of the WEIGHT PLATES (105) are all facing the right way.

•   Insert four CAP PLUGS (106) into the top and bottom ends of the GUIDE RODS (36) as shown in FIGURE 11.

•   Slide the head plate assembly down over the GUIDE RODS (36) onto the weight stack.

•   Attach the WEIGHT STACK LABELS (104) to the weight stack. Also insert the WEIGHT STACK PIN (75) into the first

WEIGHT PLATE (105) of the weight stack.

106

36

105

 1

73

91

75

104

70

71

34

83 3/8 X 1-1/4”

72

106

Summary of Contents for 425103









































Reviews:

No comments

Brands by name

Popular brands

Load more brands