ParaBody 375101 Assembly Instructions Manual Download

Page: 12 / 22

FIGURE 13

FIGURE 14

STEP 14

• Snap two WEIGHT PLATE BUSHINGS (28) each, into

the top side of fifteen WEIGHT PLATES (31) as shown
in FIGURE 13.

STEP 13

SECURELY

tighten two 5/16” SET SCREWS (57) to the collars on the end of the PRESS ARM (3) as shown in FIGURE 13.

• Slide one 3/4 DIA X 11" SHAFT (25) through PRESS ARM (3), PRESS ARM ADJUST (7), and TOP BOOM (5) as shown in FIGURE 13.

SECURELY

assemble one 1/2” SPRING PIN ASSEMBLY (37) into the SPRING PIN BARREL on the PRESS ARM (3). Pull back on spring

pin until it engages with one of the slots in the PRESS ARM ADJUST (7).

37 1/2” SPRING PIN

63 3/8 X 1-1/4”

2. Assemble two 3/8 X 1-1/4” BOLTS (63) and two 3/8” WASHERS (51) to the 3/4” DIA X 11” SHAFT (25) as shown in FIGURE 12.

(NOTE:

SIMULTANEOUSLY

tighten bolts, then back nut off 1/4 turn to allow the PRESS ARM (3) to rotate freely.)

• Slide the PRESS ARM (3) over the PRESS ARM ADJUST (7) as shown in FIGURE 13.

Use the following sequence to tighten the PRESS ARM:

1. Center PRESS ARM (3) and PRESS ARM ADJUST (7) over the BENCH FRAME (2) and have someone firmly hold in place until

sequence 3 is completed..

5. If further adjustment is necessary, loosen the bolts securing the TOP BOOM (5) to the BASE (1) and BENCH FRAME (2), reposition

TOP BOOM accordingly and retighten.

IMPORTANT! Follow sequence below.

Summary of Contents for 375101























Search results

Summary of Contents for 375101

Reviews:

Related manuals for 375101

Brands by name

Popular brands

ParaBody 375101, Assembly Instructions Manual

Search results

Summary of Contents for 375101

Reviews:

Related manuals for 375101

Brands by name

Popular brands