Or you can select 10~90%, if your RUN TIME set up 10mins and up. It has regular stops of 10
minutes during every section of RUN TIME. Otherwise, you only can select 50% or 100% when
the RUN TIME set up value under 10mins.
The reading of “100” is flashing and press button
Zone 1
to increase the digital value (or press
button
Zone 2
to decrease the digital value) until the selected value is entered, press button
Item
to
save the value. <the digital values range is from 10~100%>
The MIST CYCLE is now set and program proceeds further to set CYCLE TIME automatically.
Example:
If given RUN TIME = 50min, and
MIST CYCLE = 20%
The timer waters for 10 minutes, stop 10 minutes, then repeat.
Number of watering times = 100%
÷
20% = 5 times
5 times x 10 min. = 50 minutes
Total irrigation time is : 5times x 10min + 4stops x 10min = 90minutes
If given RUN TIME = 50min, and
MIST CYCLE = 100%
The timer waters for 50 minutes, then stop.
(g)
Set the CYCLE TIME:
According to pre-set value of RUN TIME and MIST CYCLE, the program will calculate the
minimum value of CYCLE TIME automatically. If programmed value of CYCLE TIME to be
revised, press button
Zone 1
to increase the digital value (or press button
Zone 2
to decrease the
digital value) until the selected value is entered, press button
Item
to save the value. <the digital
values range is from 1HR, 2HR, 3HR, 4HR, 6HR, 8HR, 12HR, 1 DAY, 2 DAY, 3 DAY, 4 DAY, 5
DAY, 6 DAY, 7 DAY, >
The CYCLE TIME is now set and program proceeds further to set Watering Days mode.
Example of calculation of minimum CYCLE TIME:
If given RUN TIME = 100 min.
MIST CYCLE = 30% (the timer waters for 30mins, stops 10mins, then repeat.)
Number of watering times = 10
0mins ÷ 30mins = 3 times x 30mins and 10mins sur
plus (means min.
watering times is 4)
3 stops x 10min + 100mins = 130mins (Total minutes of RUN TIME + MIST CYCLE)
130mins
÷ 60mins = 2 hours and 10 min. Rounding
-off as 3 hours.
So, CYCLE TIME is programmed as 3 HR automatically.
(h)
Set the WATERING DAYS:
A icon of raindrop is blinking on the left side of MO (Monday) at the beginning. Press button
Zone 1
to
select the watering days of the week, or press button
Zone 2
to skip it. Icon of the raindrop will be
stuck to the side of selected days of week, when press button
Zone 1
and then shown in blinking on
next day of week until each of 7 days in the week has been gone through one after another. Press Item to
save the selected watering days.
The WATERING DAYS and now set and program proceeding further to set Prog. ON/OFF
(i)
Set the Prog. ON/OFF:
When the procedures from (a) to (h) are all set properly, the＂ON＂will be blinking. Press button
Zone
1
or
Zone 2
to select “ON＂or “OFF＂. If you select “ON＂, which means executing all settings
right away or
“OFF＂which means reserving all settings without execution and then press button
Item
to save whole the programmer for Zone 1.
(j)
Set the program for ZONE 2:
The reading “12” of ZONE 2 start flashing, repeat above step from (a) to (i), you can set up the
program of ZONE 2 easily.
Finally, press button Menu/O.K. to confirm all set up programmer for ZONE 1 and ZONE 2. At
