manualshive.com logo in svg

Pantech G310, Service Manual

Share
Download
Pantech G310 Service Manual Download Page 39

G310 Service Manual  
                                                                                                                                                                                  

 

PANTECH  

R&D 

CONFIDENTIAL 

38

 

6.2.3 Side Tone Not transmitted ( Ear-piece ) 

Repeat 6-2-1 No receiving tone heard.( Ear-piece ) 

1. Check to see if Mic + pin is around 1.8V : CP125 

NO   Check that R102, C181 and R104 is cold solder, broken, short to the other  

PCB pattern or not  

      If you find out any defective part, you replace it.  

Set to HP8922M to connect a call and then set to 1kHz with Echo audio mode. 

2. Check U102.J10 (C132) pins for wave form : CP126 

       NO  Replace MIC  

 

6.2.4 Side Tone Not transmitted ( Hands-free Mic. ) 

Repeat 6-2-2 No receiving tone heard.( Hands-free Earphone ). 

1. Check to see if U102. H10 (C130) pin is 2.5V : CP127 

NO   Check that R107, R108, C150 and C151 is cold solder,broken,short to the other  

                   PCB pattern or not. 

      If you find out any defective part, you replace it.  

Set to HP8922M to connect a call and then set to 1kHz with Echo audio mode. 

3. Check U102. H10 (C130) pins for wave form : CP127 

NO   Replace Handsfree Mic. 

 

 

 
 
 
 
 
 
 

 

 

CP125 

CP126 

CP127 

CP125 

Summary of Contents for G310





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands