background image

INSTRUCTIONS CM365

© Panduit Corp. 2008

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

Keyed Knockout
Slots for Wall
Mount applications
(6 places)

Brackets for 
Fire Resistant Foam (2 places) 

RP-TNC 
Wall Mount 
bulkhead 
connector 
knockout
(6 places)

Double Knockout 
for 1/2” or 3/4” Conduit
(3 places)

Knockouts
for Surface
Raceway
(2 places)

Knockouts for 
led lights 
on the wap 

#10-32 
Threaded
Grounding 
Studs

Antenna knockouts for
6 internal antenna 
mounting applications

RP-TNC Ceiling Mount
bulkhead connector 
knockout (6 places)

Knockout for
electrical 
junction box

(door removed from view for clarity)

(4)#10-32 Hex Nuts
(4)#10 Split Lock Washers
(4)#8-32 Hex Nuts
(4)#8 Split Lock Washers
(2)#6-32 Screws
(1)Grounding Cable
(4)Pieces of Fire Resistant Foam
(1)26" length Grommet Edging
(1)2 Position Surface Mount Box
     (

PANDUIT

 Part No. CBXJ2WH-A)

PZWIFIEN ONLY

(1)2' long Category TX6 Plus Patch Cord
     (

PANDUIT

 Part No. UTPSP2)

(1)Category TX6 Plus Jack Module
     (

PANDUIT

 Part No. CJ688TGWH)

#6-32 Screws

#8-32           #8

Hardware Guide

List of Common Components:

#10-32           #10

Hardware Guide

#10-32 Screws

PZWIFIEN

(2)

P

AN

-T

Y

 mounts

     (

PANDUIT

 Part No. ABMM-A-C)

(4)

P

AN

-T

Y

 Cable Ties

     (

PANDUIT

 Part No. PLT1.5I-C)

(1)Foam Retention Plate
(2)Keys
(2) Latching Wire Clips 
      (Panduit Part No. LWC50-A-L)
(4) # 10-32 X 3/8” Thread Cutting 
Screws

PZWIFIENS ONLY 

(1) Minicom TX6 plus shielded jack
     (CJS666TGY)
(1) 1M STP TX6 plus patch cord
     (STP6X1MBU)

TABLE OF CONTENTS

 

Page (s)

Wall Mount Installation..................................................................................................................................................... 2
Ceiling Mount Installation..................................................................................................................................................2-4
Cisco Aironet 1250 Series Access Point Installation........................................................................................................ 5
Cable Routing....................................................................................................................................................................6
Alternate Wall Mount Installation with External Mount Antennas.......................................................................................7
Alternate In-Ceiling Installation with External Mount Antennas..........................................................................................8

Page 1 of 8

P

AN

Z

ONE

 

Wireless Access Point Enclosure

Part Numbers: PZWIFIEN, PZWIFIENS

Summary of Contents for PZWIFIEN









Reviews: