background image

DP

O

E™

 Power System User Manual 

 

Part Number: PN380C 

POWER PLANT MOUNTING AND WIRING 

 

WARNING: 

Ensure all AC and DC power sources are off and disconnected. 

 

 

 

 

8

 

 

 
Mechanical Mounting 

The 

DP

O

E™

 Power System chassis is installed in a standard EIA 19” rack. It is recommended that one 

person lift the chassis into the proper rack place while another person installs the supplied mounting 
screws.  Tighten the screws with a torque wrench to the setting according to 

Table 6: Recommended 

Torque Settings

 

Mounting Brackets 

 
  
 

 

 
 

 

Figure 5: Chassis (Front View) 

Slots for Rectifiers 

 

In shelf 

distribution 

 

Support Shelf Mounting (Optional) 

After securing the 

DP

O

E

™ Power System chassis with mounting screws in the front, an optional rack 

mount shelf may be installed underneath the chassis on the backside of the rack to alleviate potential 
sagging of the chassis unit, due to weight distribution when mounted on a 2-post rack. 

PANDUIT

 offers a 

1RU shelf (part # SRM19FM1) with a load rating of 30 lbs that will help support the chassis. For optimum 
saftety, a 2 RU shelf (

PANDUIT

 part # SRM19FM2 – shown below) with a load rating of up to 50 lbs may 

be installed.  

 

 

Attach power chassis to front of rack 

using Mounting Brackets 

Optional Rack Mount Shelf 

(attached to back of rack with 

shelf turned upside down) 

 

Figure 6: Optional Rack Mount Shelf 

 

NOTE: 

Optional rack shelf is actually installed upside down to the rear of the rack to allow 
power chassis to rest on the flat side of the shelf. 

 

Summary of Contents for DPOE


















Reviews: