background image

Doc id: ENG_OMM_SL400_SL450_P01

7/37

© Pandrol AB

1.1  Safety actions

• 

Read and understand all safety regulations and warnings before installation, operating 

or performing maintenance on this machine.

• 

Locate  emergency  stop  buttons  and  fire  extinguisher  on  the  carriermachine  before 

installation, operating or performing maintenance on this machine.

• 

It  is  essential  that  all  use,  maintenance  and  service  is  implemented  by  qualified 

personnel, trained by Pandrol AB.

• 

The machine shall not be used as a transport vehicle for personnel or equipment. Only 

sleepers are allowed to be carried with the machine.

• 

Make sure that no unqualified/unauthorized persons are in the operating area during 

installation, use or maintenance.

•  Safety regulations regarding personnel in operating area for the sleeper layer are valid 

for this attachment.

• 

Improper operation of this equipment can be dangerous and result in personnel injury 

or death. Personal eye protection and clothing must be worn when undertaking work.

• 

Improper maintenance of this equipment can be dangerous and result in personnel 

injury or death.

• 

Before maintenance work on the machine, disconnect hydraulics and electrics to the 

carrier machine.

• 

Use  and  follow  standards  and  regulations,  accident  prevention  regulations  and 

regulations concerning special ambient conditions (e.g. areas potentially endangered 

by explosive materials, heavy pollution or corrosive influences).

• 

It is of great importance that all service, component replacements or other operations 

in the electronic or hydraulic systems are accomplished by qualified personnel only.

•  The use of solvents as cleaning agents and the use of lubricants can involve health 

and/or safety hazards. The manufacturers of the solvents and lubricants should be 

contacted for safety data. The recommended precautions and procedures of the 

manufacturers should be followed.

• 

The use of an air jet, which must be less than 8 bar (116 psi), to blow parts clean or 

to blow them dry after being cleaned with a solvent will cause particles of dirt and/or 

droplets of the cleaning solvent to be airborne. These conditions may cause skin and/

or eye irritation.

•  When using an air jet do not direct it toward another person. Improper use of air jet 

could result in bodily injury.

Summary of Contents for Rosenqvist SL400






































Reviews: