Panasonic YT-40MFW Operating Instructions Manual Download Page 15

Page: 15 / 15

Panasonic Welding Systems (Tangshan) Co., Ltd.

Add

：

No.9 Qingnan Road, New & Hi-Tech Development Zone, Tangshan,Hebei, China

Post Code

：

063020

Tel

：

400-612-5816

URL

：

http://pwst.panasonic.cn/

Panasonic Welding Systems (Tangshan) Co., Ltd.2020

2020-12

Printed in China

【

The standard of the product

】

This product is designed and manufactured according to EN IEC 60974-7:2019.

This product may not conform to the local laws and standards of other countries.

Please be absolutely sure to consult with us before attempting to relocate or resell

this product to other countries.

【

ATTENTION: The disposal of the product

】

In case of disposal of the product, please sign the assignment agreement on

disposal treatment with the authorized organization and then assign the organization

to dispose the product.

Summary of Contents for YT-40MFW
















Search results

Summary of Contents for YT-40MFW

Reviews:

Related manuals for YT-40MFW

Brands by name

Popular brands

Panasonic YT-40MFW, Operating Instructions Manual

Search results

Summary of Contents for YT-40MFW

Reviews:

Related manuals for YT-40MFW

Brands by name

Popular brands