Cable preparation (continued)
Installation
Connecting wires
Step.1 Preparations
➀
There are 3 methods to install the camera as follows.
In accordance with the conditions of the installation location, prepare the foundation of the installation
site, fix the installation support and the installation stand, and prepare for cable wiring.
• Stationary installation ∙ ∙ ∙ Install on a concrete stand, etc. (Side wiring)
• Pole installation ∙ ∙ ∙ Install on the top of a thick metal pole. (Bottom or side wiring)
• Ceiling installation ∙ ∙ ∙ Install on a concrete ceiling. (Side wiring)
➁
Procure locally the following parts depending on the camera mounting method used for the specific
installation location.
■
To weld the bolt on the installation stand
• M8 nut .............................................................................................8 pcs. (To fix with double nuts)
• M8 flat washer / spring washer ............................................................................... 4 pcs. for each
■
To cast the anchor on the installation stand
• M8 anchor / bolt ..................................................................................................... 4 pcs. for each
• M8 flat washer / spring washer ............................................................................... 4 pcs. for each
■
To fix the safety wire
• M8 anchor / screw .................................................................................................... 1 pc. for each
Step.2 Work on the installation surface.
Weld the bolt or cast the anchor on the installation site.
This section describes the case of fixing with screws by casting the anchor.
Listed below are the dimensions of the mounting portion (the position and fitting diameters).
■
To fix the camera directly on the installation surface
■
To fix the camera with the attachment plate
Front view
4-ø10 mm
{13/32 inches}
170 mm {6-11/16 inches}
170 mm {6-11/16 inches}
142 mm {5-19/32 inches}
142 mm {5-19/32 inches}
71.8 mm {2-13/16 inches}
71.8 mm {2-13/16 inches}
48 mm {1-7/8 inches}
34 mm {1-11/32 inches}
Front view
Safety wire
fixing hole
4-ø10 mm
{13/32 inches}
71.8 mm {2-13/16 inches}
71.8 mm {2-13/16 inches}
55 mm {2-5/32 inches}
34 mm {1-11/32 inches}
Max. 300 mm
{11-13/16 inches}
Bottom view of WV-SUD638
Bottom view of the attachment plate
Step.3 Take the camera out of the packaging box.
Hold the handle of the protection bag, pull up the unit from the box, and put it upright as shown in the
illustration.
Step.4 Prepare for removing the side cover of the mounting pedestal
• Open the camera protection bag.
• Loosen the 2 side cover fixing screws with the bit (accessory),
and remove the side cover from the mounting pedestal.
Step.5 If necessary, install the IR LED unit
(WV-SUD6FRL1: Optional) to the camera.
For detailed installation instructions, refer to the Operating
Instructions of the IR LED unit.
Step.8 Mount the camera onto the installation surface.
■
To fix the camera directly on the installation surface
■
To fix the camera with the attachment plate
Camera fixing
screws × 4
(locally
procured)
Spring washers,
flat washers
× 4 each (locally
procured)
Spring washer
× 4 (accessory)
Attachment plate fixing screws × 4 (locally procured)
Attachment
plate
(accessory)
Flat washer
× 8 (accessory)
Fixing nuts for attachment
plate × 4 (accessory)
Fixing screws for
attachment plate
× 4 (accessory)
IMPORTANT:
• Before lowering the camera onto the installation surface, thread cables or wires through the
bottom wiring port or the side wiring port.
• Recommended tightening torque for mounting the attachment plate: 11.76 N∙m {8.67 lbf·ft}
• Min. pull-out strength of fixing screws for the camera or the attachment plate ∙ ∙ ∙ 1539 N {346 lbf} (per 1 pc.)
Step.9 Fix the safety wire.
Fix the safety wire on the base of a building or on an area with sufficient strength (with a min. pull-out
strength of 1539 N {346 lbf} or above). Please procure M8 fixing screws locally in accordance to the
material of the installation location.
Perform Step 7 and subsequent steps at the installation location.
Exercise care when executing the steps.
Step.7 Install the safety wire (accessory) to the camera
Tilt the camera over sideways with the buffer material in the packaging material, and as shown in
the illustration below, install the wire clamper (accessory) and the safety wire (accessory) to the wire
mounting holes at the bottom of the camera.
Wire clamper
(accessory)
Safety wire (accessory)
Wire mounting hole
Camera bottom
Note:
• Please peel off the release paper of the double-sided tape attached on the bottom side of the
wire clamper before use.
• The safety wire can be pulled out from 2 directions. Install the wire clamper at the pulling direc-
tion of the safety wire.
IMPORTANT:
• The installation surface is horizontal.
• To weld the anchor bolt to the mounting portion, the maximum part of the threaded length is
40 mm {1-9/16 inches} and the minimum is 30 mm {1-3/16 inches}.
• Minimum pull-out strength: ∙ ∙ ∙ 1539 N {346 lbf} (per 1 pc.)
• Fully consider the fixing screws for camera body or attachment plate fixing to installation area,
such as using corrosion resistance treated screws or performing caulking.
IMPORTANT:
• To operate the camera temporarily for settings or other
purposes, be sure to keep the camera in the upright
position when connecting it to the power supply. After the
camera is connected to the power supply, initial opera-
tions will begin automatically. Please ensure that the cam-
era is not obstructed by your hand or other objects when
it starts panning, tilting or performing other actions.
IMPORTANT:
• When using the camera in standing position, ensure that it does not topple over. Fix it temporarily on
the included attachment plate (see Step 8), or ensure proper support before any work is done on it.
• Use the handle of the protection bag only to take the camera out of its packaging box. Do not
use it to hang the camera in high places.
[1] Connect the waterproof EXT I/O connector (accessory) to the camera.
Alignment
mark (C)
Alignment
mark (D)
Part B
Part A
Plug
Receptacle
Mounting portion
of the camera
• Remove the cap attached to the receptacle for the waterproof EXT I/O connector of the camera.
(Do not remove the cap if the waterproof EXT I/O connector is not used.)
• During installation, align the alignment mark (D) on part A of the plug with the alignment mark (C) of
the receptacle, and push it straight in.
• To remove the plug when it is still connected, hold the coupling part B of the plug and pull it out
straightly.
Note:
• Always turn off the circuit’s power supply before connecting or disconnecting the connector.
• Insert the connector with a force of 30 N {6.74 lbf} or above.
• After the connector is connected, do not apply any load of 30 N {6.74 lbf} or above on the cable.
[2] Connect the waterproof power supply connector (accessory) to the camera.
• Remove the cap attached to the receptacle for the waterproof power supply connector of the camera.
(Do not remove the cap if the waterproof power supply connector is not used.)
• During installation, align the guide of the plug with that of the receptacle, and then push it straight in.
(The guides can be aligned by lightly inserting the plug on the receptacle and rotating the plug.)
• Rotate the plug’s coupling nut, and fix it firmly on the receptacle.
Recommended tightening torque: 1.0 ~ 1.5 N∙m {0.74 ~ 1.11 lbf∙ft}
Guide
Receptacle
Receptacle
Coupling nut
Plug
Plug
Coupling nut
[3] Connect the waterproof RJ45 connector (accessory) to the camera.
• Insert the waterproof RJ45 connector into the receptacle of the camera.
Receptacle
Waterproof RJ45 connector
• Rotate the ring of the waterproof RJ45 connector, and fix it firmly on the receptacle.
Recommended tightening torque: 1.0 ~ 1.5 N∙m {0.74 ~ 1.11 lbf∙ft}
Ring
Receptacle
Waterproof RJ45 connector
[4] Install the side cover.
Install the side cover removed in “Step 4 Prepare for removing the side cover of the mounting pedestal”
in “Installation.” back to its original position with 2 screws.
(Recommended tightening torque:1.5 N∙m {1.11 lbf·ft})
IMPORTANT:
• After installation and before connection to the power supply, please check the following items.
➀
Every waterproof connector is properly installed.
➁
The wiring and power supply voltage of the wired power cables are correct.
➂
The camera is not exposed directly to the sun or other light sources.
➃
There is no obstruction in the surroundings. (After the camera is connected to the power
supply, initial operations will begin automatically. Please ensure that the camera is not
obstructed by your hand or other objects when it starts panning, tilting or performing other
actions.)
[5] Remove the buffer material and the protection sheet from the camera.
[6] Connect the camera to the power supply.
For details on the follow-up procedure, refer to the leaflet “Configuring the camera so that it can be
accessed from a PC”.
Side cover
Side cover fixing screws × 2
Mounting
pedestal
Note:
• Keep the removed side cover in a safe place as it will be
mounted again in the end.
IR LED unit
[3] Attach the waterproof RJ45 connector (accessory) to the Ethernet cable.
<Locally procured items>
• Ethernet cable
Use 4 pairs (8 pins in total).
Max. length: 100 m [328 ft]; external diameter: ø5 mm ~ 6.5 mm {ø3/16 ~ 1/4 inches}
• Crimping tool for RJ45 plug (used for crimping the RJ45 plug to the Ethernet cable.)
➀
Crimp the RJ45 plug to the Ethernet cable, and thread the waterproof nut, the waterproof
rubber and the support rubber in sequence.
(There are mounting slits on the waterproof rubber
and the support rubber.)
➁
Pass the RJ45 plug through the waterproof RJ45 connector.
(As shown in the lower left illustration, there is an outlet of the same shape as the RJ45 plug on the
waterproof RJ45 connector. Please take note of the direction and insert from the inside.)
Waterproof RJ45 connector
RJ45 plug outlet
RJ45 plug
Support rubber
Waterproof rubber
Waterproof nut
➂
Insert the support rubber and the waterproof rubber into the waterproof RJ45 connector.
(Insert the support rubber first, and then insert the waterproof rubber into the rear end of the
waterproof RJ45 connector until it touches the inside of the nail.)
The nail part on the rear
end of the waterproof
RJ45 connector
Support rubber Waterproof rubber
➃
Mount the waterproof nut from the rear end of the waterproof RJ45 connector, and tighten it.
Recommended tightening torque:
0.5 ~ 1.5 N∙m {0.37 ~ 1.11 lbf·ft}
Waterproof nut
Note:
• If a washer nozzle is used, prepare the washer nozzle mounting bracket (accessory) in advance,
and then install the washer nozzle and fix it while fixing the camera as described in Step 8 at the
same time.
• Please install the washer nozzle mounting bracket A with the “FRONT” mark facing the front of
the camera (on the Panasonic logo side).
• After checking the installation, adjust the direction of the washer nozzle to ensure that the front
glass is hit by water flow.
<To install the washer nozzle>
<To fix the washer nozzle mounting bracket>
➀
Washer nozzle mounting bracket A
Applicable nozzle size: ø16 mm {5/8 inches}
Washer hose
fixing holes × 4
Camera fixing
screws
× 4 (locally
procured)
FRONT
mark
Washer nozzle
mounting
bracket A
(accessory)
Washer hose
(locally
procured)
R4 mm {5/32 inches}
Handle
Protection bag
Fixing screws for the
washer nozzle mount-
ing bracket B
× 2 (accessory)
Washer nozzle
Washer nozzle
mounting bracket A
(accessory)
FRONT
REAR
➁
Washer nozzle mounting bracket B
6 mm {1/4 inches}
Applicable
nozzle size
Front view
IMPORTANT:
• Attach the safety wire so that if the
camera were to become detached,
it would not fall on nearby people.
Washer nozzle mounting bracket B (accessory)
Safety wire fixing
screws
(locally procured)
Safety wire
(accessory)
9
Step.6 If necessary, bend the camera’s tilt arm forward.
To shoot the foot area of the camera installed, change the settings of the tilt arm to an approximate 45°
incline. Please do as instructed below.
➀
Remove the 2 tilt arm fixing screws on the
left side of the camera.
• Loosen the support arm cover fixing screw
with an hex wrench (locally procured), and
remove the support arm cover from the
camera body.
• Remove the 2 tilt arm fixing screws from the
inside on the left.
Note:
• The removed support arm cover and the
2 screws will be reused after the tilt arm is
bent forward.
➁
Remove the 4 tilt arm fixing screws from
the right side of the camera.
• Loosen the 2 tilt cover cap fixing screws with
an hex wrench (locally procured), and remove
the tilt cover cap and the rubber cap from the
camera body.
• Remove the 4 tilt arm fixing screws from the
inside on the right.
Note:
• The removed tilt cover cap, the rubber
cap, and the 4 screws will be reused after
the tilt arm is bent forward.
➂
Ensure that the camera does not topple over, and bend the tilt arm
to an approximate 45° incline.
➃
Keep the TILT arm position tilted by an angle of 45°and re-fix the
screws and the covers removed in
➀
and
➁
.
Tilt arm fixing screws: (Recommended tightening torque: 1.5 N∙m {1.11 lbf·ft})
Covers
: (Recommended tightening torque: 1.37 N∙m {1.01 lbf·ft})
Note:
• Repacking is impossible when the tilt arm is bent 45°. If the camera
needs to be moved from the preparation area to the installation
location, execute Step 6 in the vicinity of the installation location.
• Be sure to attach the rubber cap and the rubber washers on the
three fixing screws used to fix covers.
Support arm cover
Tilt arm fixing screws × 2
Support arm cover fixing
screw
Left side of the camera
Tilt arm fixing screws × 4
Rubber cap
Tilt cover cap
Tilt cover cap fixing
screws × 2
Right side of the camera
* Pass the cable tie for fixing the washer hose
through the washer nozzle mounting bracket A
first, and then, secure the washer nozzle
mounting bracket A together with the camera.
