background image

Do not damage the power cable. 

Do not damage, fabricate, twist, stretch, bundle, or forci-
bly bend the power cable. Do not place heavy objects on 
it, and keep it away from heat sources. 
Use of a damaged power cable may cause electric shock, 
short circuit, or fire. 
Consult the dealer for repair.

Correctly perform all wiring

Short circuits in the wiring or incorrect wiring may cause 
fire or electrical shock.

Turn the power off when cleaning this product. 

Failure to observe this may cause injury. 

Do not rub the edges of metal parts with your hand. 

Failure to observe this may cause injury.

[Precautions for use]

This product is designed to be used indoors. This 
product is not operable outdoors.

This product has no power switch.

When turning off the power, disconnect the power supply 
from the 12 V DC power supply or the PoE device.

To keep on using with stable performance

Do not use this product in hot and humid conditions for a 
long time. Failure to observe this causes component deg-
radation resulting in life shortening of this product. Do not 
expose this product to direct heat sources such as a 
heater.

Handle this product with care.

Do not drop this product, nor apply shock or vibration to 
the product. Failure to observe this may cause trouble.

About the battery

A battery is installed inside the camera.
Do not leave the battery exposed in environments of 
excessive heat as a result of sunlight or fire.

About the PC monitor

When displaying the same image on the monitor for a long 
time, the monitor may be damaged. 
It is recommended to use a screen-saver. 

When an error is detected, this product will restart 
automatically. 

This product will be inoperable for around 2 minutes after 
the restart just as when the power is turned on. 

Product disposal/transfer

Data saved on this product or a storage device used with 
this product may lead to personal information leakage. 
When it is necessary to dispose or give this product to 
someone, even when for repair, make sure that there is no 
data on this product.

When disposing of a device that stores data, we recom-

mend you delete all of the stored data using a PC and 

then physically destroy the device.

Do not hold the dome section.

The dome section of this unit rotates 360 °. When remov-
ing this unit from a ceiling or wall, turn the unit while hold-
ing the fixed section.

Cleaning this product body

Be sure to turn off the power before cleaning. Failure to 
observe this may cause injury. Do not use benzine, 
thinner, or any other types of solvents, when cleaning this 
product. Otherwise, it may cause discoloration. When 
using a chemical cloth for cleaning, read the caution 
provided with the chemical cloth product.

IMPORTANT:

  • 

The camera position may be moved inadvertently while 
cleaning the camera body. Restart the camera or 
refresh the camera position (position refresh) to correct 
the camera position. Refer to the Operating Instructions 
on the provided CD-ROM for further information. 

 

Make sure that the product does not become wet.

Keep this camera away from water and moisture.

Transmission interval

Image transmission interval may become slow depending 
on the network environment, PC performance, shooting 
subject, access number, etc. 

About SD memory card

  •  Before removing the SD memory card, make sure to 

select “Not use” for “SD memory card” on the [SD 
memory card] tab of “Basic” page on the setup menu 
first. (

 Operating Instructions (included in the 

CD-ROM))  Refer to page 16 for descriptions of how 
to insert/remove an SD memory card. 

  •  When using an SD memory card, format it using this 

product. Recorded data on the SD memory card will 
be deleted when formatted. If an unformatted SD 
memory card or an SD memory card formatted with 
other devices is used, this product may not work 
properly or performance deterioration may be caused. 
Refer to the Operating Instructions on the provided 
CD-ROM for how to format an SD memory card. 

  •  When  some  SD  memory  cards  are  used  with  this 

product, the product may not work properly or perfor-
mance deterioration may be caused. Use the SD 
memory cards recommended in page 33. 

10

Summary of Contents for WV-SC588A









































Reviews: