Panasonic WV-NF284 - i-Pro Network Camera Network Operating Instructions Download Page 2

Page: 2 / 56

CONTENTS

Preface ............................................................................................................................ 3

About these operating instructions .............................................................................. 3

Trademarks and Registered Trademarks ................................................................... 3

Viewer Software .......................................................................................................... 3

Monitor Images on a PC .................................................................................................. 4

Monitor images from a single camera ......................................................................... 4

Monitor images from multiple cameras ....................................................................... 7

Action at an Alarm Occurrence ....................................................................................... 8

Transmit Images onto an FTP Server ............................................................................. 9

Transmit an alarm image at an alarm occurrence

(Alarm image FTP transmission) ................................................................................. 9

Transmit images at a designated interval or period (FTP periodic transmission) ....... 9

Save images on the SD memory card when failed to transmit images by the

FTP periodic transmission function ............................................................................. 10

About the network security of this unit ............................................................................. 12

Equipped security functions ........................................................................................ 12

Display the Setup Menu and Configure the Settings of the Camera using a PC ............ 13

How to display the setup menu ................................................................................... 13

How to operate the setup menu .................................................................................. 14

Configure the basic settings of the camera [Basic setup] ........................................... 17

Configure the settings relating to images and audio [Camera setup] ......................... 21

Configure the multi-screen settings [Multi-screen setup] ............................................ 26

Configure the alarm settings [Alarm setup] ................................................................. 27

Configure the settings relating to the authentication [Authentication setup] ............... 34

Configure the settings of the servers [Server setup] ................................................... 36

Configuring the network settings [Network setup] ....................................................... 38

Maintenance of the camera [Maintenance] ................................................................. 46

About the Displayed System Log .................................................................................... 49

Troubleshooting ............................................................................................................... 51

Summary of Contents for WV-NF284 - i-Pro Network Camera
























































Search results

Summary of Contents for WV-NF284 - i-Pro Network Camera

Reviews:

Related manuals for WV-NF284 - i-Pro Network Camera

Brands by name

Popular brands

Panasonic WV-NF284 - i-Pro Network Camera, Network Operating Instructions

Search results

Summary of Contents for WV-NF284 - i-Pro Network Camera

Reviews:

Related manuals for WV-NF284 - i-Pro Network Camera

Brands by name

Popular brands