background image

1. Do not attempt to disassemble the camera.

To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside.  Ask qualified service personnel for servic-
ing.

2. Handle the camera with care.

Do not abuse the camera.  Avoid striking, shaking, etc.  The camera could be damaged
by improper handling or storage.

3. The following installation should be made by qualified service personnel or

system installers.

4. Do not use strong or abrasive detergents when cleaning the camera body.

Use a dry cloth to clean the camera when dirty. When the dirt is hard to remove, use a
mild detergent and wipe gently. Then wipe off the remaining detergent with a dry cloth.

5. Clean the CCD faceplate with care.

Do not clean the CCD with strong or abrasive detergents.  Use lens tissue or a cotton
tipped applicator and ethanol.

6. Never face the camera towards the sun.

Do not aim the camera at bright objects.  Whether the camera is in use or not, never
aim it at the sun or other extremely bright objects.  Otherwise, blooming or smear may
be caused.

PRECAUTIONS

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

N0502-0

3TR001106AAA

Printed in Japan

N

19

Panasonic's WV-CW474FE colour digital camera introduces a new level of high picture qual-
ity and high resolution through the use of a 1/3-inch interline transfer CCD image sensor
having 752 horizontal pixels (picture elements), and digital signal processing LSIs.  This
model offers cutting-edge technology for advanced video surveillance.

PREFACE

Colour CCTV Camera

Operating Instructions

Model No.

WV-CW474FE

The serial number of this product may be found
on the top of the unit.
You should note the serial number of this unit
in the space provided and retain this instruction
as a permanent record of your purchase to aid
identification in the event of theft.

Model No. 

Serial No. 

WARNING:

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER SER-

VICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

Wij verklaren als enige aansprakelijke, dat het product
waarop deze verklaring betrekking heeft, voldoet aan de
volgende normen of andere normatiefve dokumenten,
overeenkomstig de bepalingen van Richtlijnen 73/23/
EEC en 89/336/EEC.

Vi erklærer os eneansvarlige for, at dette produkt, som
denne deklaration omhandler, er i overensstemmelse
med den følgende standarder eller andre normative
dokumenter i følge bestemmelserne i direktivene 73/23/
EEC og 89/336/EEC.

Vi deklarerar härmed värt fulla ansvar för att den produkt
till vilken denna deklaration hänvisar är i överensstäm-
melse med standarddokument, eller andra normativa
dokument som framstölls i Direktiv 73/23/EEC och 89/
336/EEC.

Ilmoitamme yksinomaisella vastuullamme, että tuote, jota
tämä ilmoitus koskee, noudattaa seuraavia standardeja
tai muita ohjeellisia asiakirjoja, jotka noudattavat direkti-
ivien 73/23/EEC ia 89/336/EEC. säädöksiä.

Vi erklærer oss alene ansvarlige for at produktet som
denne erklæringen gjelder for, er i overensstemmelse
med følgende normer eller andre normgivende doku-
menter som fælger bestemmelsene i direktiven 73/23/
EEC og 89/336/EEC.

We declare under our sole responsibility that the product
to which this declaration relates is in conformity with the
standards or other normative documents following the
provisions of Directives EEC/73/23 and EEC/89/336.

The exclamation point within
an equilateral triangle is intend-
ed to alert the user to the pres-
ence of important operating
and maintenance (servicing)
instructions in the literature
accompanying the appliance.

The lightning flash with arrow-
head symbol, within an equilat-
eral triangle, is interned to alert
the user to the presence of
uninsulated "dangerous volt-
age" within the product's enclo-
sure that may be of sufficient
magnitude to constitute a risk
of electric shock to persons.

Summary of Contents for WV-CW474FE











Reviews: