manualshive.com logo in svg

Panasonic WJMP204C - DATA MULTIPLEX UNIT, Operating Instructions Manual

Share
Download
Panasonic WJMP204C - DATA MULTIPLEX UNIT Operating Instructions Manual Download Page 29

29

WJ-MP204C

Function

WV-CU360C

Camera Selection

●

Alarm Reset

Alarms are reset according to the reset mode (EXT, auto (1S-5M) or OFF) selected in the ALARM OUTPUT setup.

• Manual resetting

Pressing the RESET button on the unit resets the activated alarm.
Pressing the ALARM RESET button on the controller resets the activated alarm.

• External resetting

Input to the ALARM/REMOTE terminal resets the activated alarm when the terminal is set to the alarm input mode.

• Auto resetting

Elapsing of the preset time resets the activated alarm, except for the unit's alarm indicator which remains on steady light.

●

Alarm Suspension

This function is used in the setup operation or whenever you do not wish to accept alarm inputs.

Press the ALARM SUSPEND button on the front panel, or ALM SUSPEND on the controller. Alarm inputs will be ignored
while the indicator is lit.
Press the button again to release the alarm suspension. Alarm inputs will be accepted after the indicator turns off.

Alarm Reset

Alarm Suspend

4

3

2

1

Alarm Suspend
Reset

Enter a camera number with
numeric buttons.

CAM

SET

then

CAM

#

ALM RESET

ALM RECALL

ALM SUSPEND

ALM SUSPEND

SET

SUSPEND

ALARM

RESET

ALARM

SET

SUSPEND

ALARM

Summary of Contents for WJMP204C - DATA MULTIPLEX UNIT

































Reviews:

No comments

Brands by name

Popular brands

Load more brands