Panasonic WJ-FS28 Service Manual Download Page 7 | Manualshive

Page: 7 / 48

background image

Note on Installation :

Be sure to have your dealer install the set. Make sure
that the power switch is OFF and that the power plug
has been pulled out of the electrical outlet in advance.

Precautions for Installation :

keep a space of 5 cm or more.
Keep a space of 5 cm or more on the sides t rear and
top of the set.

Install the set at a place free of noise.
Noise may interfere if the cables of the set are close to
the house electric wires. In such a case, rewire the set
or change its place.

4

Mounting into the Rack

When this unit is to be mounted on a EIA 19-inch rack,
use Rack Mount Angles (provided) and 8 Rack Mount
Angle Fixing Screws (provided, M4 X 10)

1. Turn off the power of this unit.

2. Remove four rubber feet by removing four screws on

the bottom of this unit.

3. Place the Rack Mount Brackets on both sides of this

unit and tighten with the eight supplied screws.

4. Install the unit with Rack Mount Brackets in the rack by

using four screws (local procurement).

Cautions :

Do not block the ventilation opening or slot on the cover
to prevent the unit from rising temperature.
Always keep the temperature in the rack within 50°C.
Secure the rear of the unit to the rack by using addition-
al mounting angles (procured locally) when the vibration
is added to the rack.

Remove four Rubber Feet.

Fasten four screws.

5 cm or more

5 cm or more

5 cm or more

«
...
5
6
7
8
9
...
»

Summary of Contents for WJ-FS28

















































Reviews:

No comments

Related manuals for WJ-FS28

Brand: Triplett Pages: 11

Brand: Kusam-meco Pages: 16

Brand: Kusam-meco Pages: 19

Brand: Kusam-meco Pages: 16

Brand: Kusam-meco Pages: 20

Brand: YOKOGAWA Pages: 2

Brand: Giga-tronics Pages: 14

Brand: B+K precision Pages: 4

Brand: YATO Pages: 52

Brand: Sangoma Pages: 30

Brand: BST Pages: 2

Brand: Sanwa Pages: 44

Brand: Multimetrix Pages: 2

Brand: VOLTCRAFT Pages: 80

Brand: VOLTCRAFT Pages: 104

Brand: VOLTCRAFT Pages: 156

Brand: Techroutes Pages: 16

Brand: Iskra Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands