Panasonic WH-MHF09G3E5 Service Manual Download Page 85

Page: 85 / 138

16.5 Self-diagnosis Method

16.5.1 Connection Capability Rank Abnormality (H12)

Malfunction Decision Conditions:

During startup operation of heating, the capability rank of indoor checked by the outdoor is used to determine
connection capability rank abnormality.

Malfunction Caused:

1  Wrong model interconnected.
2  Wrong indoor unit or outdoor unit PCB (main) used.
3  Faulty indoor unit or outdoor unit PCB (main).

Abnormality Judgment:

Continue for 90 seconds.

Troubleshooting:

Match the compatible

model.

Check indoor and outdoor

units model number.

Matched compatibility?

Is the indoor and outdoor
model number matched?

Check the spare part numbers of
the indoor and outdoor unit PCBs
and compare with their Part Lists.

Yes

Change for specified indoor
or outdoor unit PCB (main).

Replace the indoor and

outdoor unit PCBs (main).

Summary of Contents for WH-MHF09G3E5











































































































































Search results

Summary of Contents for WH-MHF09G3E5

Reviews:

Related manuals for WH-MHF09G3E5

Brands by name

Popular brands

Panasonic WH-MHF09G3E5, Service Manual

Search results

Summary of Contents for WH-MHF09G3E5

Reviews:

Related manuals for WH-MHF09G3E5

Brands by name

Popular brands