Panasonic VL-MWD273 Installation Manual Download Page 4

4

Note:

R

The illustrations in the supplied manual(s) may vary slightly from the actual product.

*1 VL-SWD273AZ/VL-SVD273AZ models only
*2 VL-MWD273BX/VL-MWD273ML models only
*3 VL-SWD273AZ/VL-SVD273AZ/VL-MWD273AZ models only

Precautions for installation

To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/
extension monitor in the following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.

For the doorphone

R

If a strong light is shining on the doorphone, the visitor’s face may not be distinguishable. Do not place 
the doorphone in the following locations:
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the doorphone.

R

Do not place the doorphone in locations where echoing occurs, as this will cause the doorphone to 
beep frequently.

R

Dust protection/water protection is IP54.
Only when installation work specified in this guide is properly performed and appropriate water 
protection treatment is performed.

R

Make sure the rear of the doorphone is not subject to water.

R

Depending on the installation location, condensation may form on the doorphone’s lens cover. This 
may cause images to become obscured. Condensation will dissipate as the temperature rises.

For the main monitor/extension monitor

R

Install the main monitor away from electronic appliances such as TVs, radios, personal computers, air 
conditioners, boiler control panels with intercom, home security equipment, wireless devices, or digital 
cordless phones.

R

Do not install the main monitor/extension monitor in places where it will be affected by extremely high-
frequency radio waves (near broadcasting antennas etc.). This may cause the display to flicker or an 
interrupting noise to occur.

R

Leave at least 20 cm of space above, below, and to the left and right sides of the main monitor/
extension monitor. Do not install on a wall that is deeply recessed.

R

Do not install the main monitor/extension monitor inside a wall.

R

Be sure to install the main monitor/extension monitor more than 5 m away from the doorphone.

R

The product operates in the frequency range of 1.88 GHz and 1.90 GHz with a peak transmission 
power of 250 mW (max.). Refer to the "For best performance" section in the Operating Instructions.

R

In areas surrounded by a high electrical field, disturbances may occur in the main monitor’s/extension 
monitor’s image or sound.

[Locally procured]

– Power cables (AC/DC cables), wires (for doorphone and other connections):

Prepare wires of the appropriate specification. (

a

"Wire type and length")

273_ig.book  Page 4  Friday, April 28, 2017  9:46 AM

Summary of Contents for VL-MWD273

















Reviews: