Panasonic VL-MWD273 Installation Manual Download Page 2

2

For your safety

To prevent severe injury and loss of life/
property, read this section carefully 
before using the product to ensure 
proper and safe operation of your 
product.

Preventing fire, electric shock and 
short circuits

R

Leave installation work to the 
dealer. Installation work requires 
technique and experiences. Failure 
to observe this may cause fire, 
electric shock, injury, or damage to 
the product. Consult the dealer.

R

Electrical connection work should 
be performed by certified personnel 
only. Certification is required for 
performing electrical connection 
work. Consult your dealer.

R

Use only the specified power supply 
unit and AC cable.

R

Do not attempt to disassemble or 
modify this product. Contact an 
authorised service centre for repairs.

R

Never install wiring during a lightning 
storm.

R

Do not connect non-specified devices.

R

Do not connect a power cable to a 
terminal that is not specified in this 
guide.

R

When opening holes in walls for 
installation or wiring, or when securing 
the power cable, make sure you do not 
damage existing wiring and ductwork.

R

Do not make any wiring connections 
when the power supply is turned on.

R

Do not use the supplied power supply 
unit for outdoor installations (it is for 
indoor use only).

R

Do not install the main monitor/
extension monitor in the following 
places:
– Places where the main monitor/

extension monitor may be splashed 
with water or chemicals.

– Places where there is a high 

concentration of dust, or high 
humidity.

R

Do not perform any actions (such as 
fabricating, twisting, stretching, 
bundling, forcibly bending, damaging, 
altering, exposing to heat sources, or 
placing heavy objects on the power 
cable) that may damage the power 
cable. Using the product with a 
damaged power cable may cause 
electric shock, short circuits, or fire. 
Contact an authorised service centre 
for repairs.

R

When existing chime wires are used, it 
is possible that they contain AC 
voltage.
Contact an authorised service centre.

Preventing accidents and injuries

R

Do not install or use the product in 
health care facilities if any regulations 
posted in the area instruct you not to 
do so. Hospitals or health care 
facilities may be using equipment that 
could be sensitive to external RF 
(radio frequency) energy.

R

Do not install or use this product near 
automatically controlled devices such 
as automatic doors and fire alarms. 
Radio waves emitted from this product 

WARNING

273_ig.book  Page 2  Friday, April 28, 2017  9:46 AM

Summary of Contents for VL-MWD273

















Reviews: