FAQs, etc.
•
Speci
fi
cations
•
Frequently Asked
Questions
TH-42PZ70EA, TH-42PZ70E
TH-50PZ70E
Power Source
AC 220-240 V, 50 / 60 Hz
Power
Consumption
Average use
494 W
569 W
Standby condition
0.5 W (Without DVB recording)
20 W (With DVB recording)
Display
panel
Aspect Ratio
16:9
Visible screen size
106 cm (diagonal)
127 cm (diagonal)
922 mm (W) × 518 mm (H)
1,106 mm (W) × 622 mm (H)
Number of pixels
2,073,600 (1,920 (W) × 1,080 (H)) [5,760 × 1,080 dots]
Sound
Speaker
160 mm × 42 mm × 2 pcs, 8
Ω
Audio Output
20 W (10 W + 10 W), 10% THD
Headphones
M3 (3.5 mm) stereo mini Jack × 1
PC signals
VGA, SVGA, XGA
SXGA ······ (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems /
Band name
PAL B, G, H, I, SECAM B, G, SECAM L / L’
VHF E2 - E12
VHF H1 - H2 (ITALY)
VHF A - H (ITALY)
UHF E21 - E69
CATV (S01 - S05)
CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10)
CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2
VHF R3 - R5
VHF R6 - R12
UHF E21 - E69
PAL 525/60
Playback of NTSC tape from some PAL Video re cord ers (VCR)
DVB
Digital terrestrial services via VHF / UHF aerial input.
M.NTSC
Playback from M. NTSC Video recorders (VCR)
NTSC (AV input only)
Playback from NTSC Video recorders (VCR)
•
TV signals may not be received in some areas.
Aerial - Rear
VHF / UHF
Operating Conditions
Temperature
: 0 °C - 35 °C
Humidity
: 20 % - 80 % RH (non-condensing)
Connection T
erminals
AV1 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, Q-Link)
AV2 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
AV3
VIDEO
RCA PIN Type × 1
1.0 V[p-p] (75
Ω
)
S-VIDEO
Mini DIN 4-pin
Y:1.0 V[p-p] (75
Ω
) C:0.286 V[p-p] (75
Ω
)
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
COMPONENT
VIDEO
Y
1.0 V[p-p] (including synchronization)
P
B
, P
R
±0.35
V[p-p]
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
Others
HDMI1 / 2
TYPE A Connectors
•
This TV supports “HDAVI Control 2” function.
PC
HIGH-DENSITY D-SUB 15PIN
R,G,B/0.7 V[p-p] (75
Ω
)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
Card slot
SD CARD slot × 1
Output
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
1,134 mm × 688 mm × 330 mm (With Pedestal)
1,134 mm × 641 mm × 116 mm (TV only)
1,323 mm × 802 mm × 369 mm (With Pedestal)
1,323 mm × 754 mm × 99.5 mm (TV only)
Mass
42.0 k Net (With Pedestal)
35.0 k Net (TV only)
50.5 k Net (With Pedestal)
43.0 k Net (TV only)
46
47
Problem
Actions
Screen
Sound
HDMI
Chaotic image, noisy
•
Set “P-NR” in the Picture Menu (to remove noise). (p. 22)
•
Check nearby electrical products
(car, motorcycle,
fl
uorescent lamp).
No image can be
displayed
•
Is “Colour” or “Contrast” in the Picture Menu set to the minimum?
(p. 22)
•
Check Colour system. (p. 29)
Blurry or distorted image
(no sound or low volume)
•
Reset channels. (p. 29)
No sound is produced
•
Is “Sound mute” active? (p. 9)
•
Is the volume set to the minimum?
Sound level is low
or sound is distorted
•
Sound signal reception may be deteriorated.
•
Set “MPX” (p. 22) in the Sound Menu to “Mono”. (Analogue)
•
Check Sound system. (p. 29)
Sound is unusual
•
Set the sound setting of the connected equipment to
“2ch L.PCM”.
•
Check the “HDMI1 Input” setting in the Sound Menu. (p. 22)
•
If digital sound connection has a problem, select analogue sound
connection. (p. 37)
Pictures from external
equipment are unusual
when the equipment is
connected via HDMI
•
Is the HDMI cable connected properly? (p. 40)
•
Turn Off the TV and equipment, then turn them On again.
•
Check an input signal from the equipment. (p. 44)
•
Use an equipment compliant with EIA/CEA-861/861B.
Unusual image is displayed
•
Turn off the TV with Mains power On / Off switch, then turn it on
again.
TV goes into
“Standby mode”
•
Off Timer function is activated.
•
The TV enters “Standby mode” about 30 min. after broadcasting
ends.
The remote control
does not work
•
Are the batteries installed correctly? (p. 6)
•
Has the TV been switched On?
Other
DVB
•
Due to the digital reception technologies involved, quality of the DTV signals may be relatively low in
some cases, despite good reception of analogue programmes.
Interference or
frozen / disappearing
image in DVB
•
Check “DVB Signal Condition”. (p. 30)
If “Signal Quality” or “Signal Strength” are displayed in red, check
aerial.
If problem persists, consult your local Panasonic dealer.
•
Turn the TV off with the Mains power On / Off switch, then turn it
On again.
Unable to receive signals
with a high-performance
aerial
•
Install an aerial individually for the TV and VCR
(or use a splitter).
TV
VCR
Aerial
Input
terminal
Aerial Output
Aerial Output
Aerial Input
(Individual aerial)
(Individual aerial)
Splitter
Whirling sound is heard
•
The sound is from built-in cooling fan
(not a sign of faulty operation).
FAQs
Speci
fi
cations
Note
•
Design and Speci
fi
cations are subject to change without notice. Weight and Dimensions shown are approximate.
•
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.