Panasonic VB-44210G User Manual Download Page 370 | Manualshive

Page: 370 / 394

background image

Appendix I. CPC-EX 2.3 Feature Update

Section 700-Operation

Page I-6

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Special Features

The following features marked with an “*”, UNA Transfer, UNA Call
Reversion, Forwarding to UNA for CO Held Calls, All Ring Group, Private
Password, Additional RAI Access, and All Ring Group features have been
fully tested in our laboratory but not in live Beta trials. These features are to
be considered as

Beta-level

features. If you have any difficulty with these new

features please call the BTSD Hotline in Secaucus, New Jersey, at (800) 822-
0909.

*UNA Transfer

Description

The UNA transfer feature allows a trunk call to be transferred to the UNA.
The call may be transferred manually or via a device such as an automated
attendant.

Programming

N/A

Operation

To transfer a trunk call to UNA:

1. Hookflash or press

HOLD

to place the trunk call on hold.

2. Dial

*78

. After

*78

is dialed, dial tone is heard indicating that the call has

successfully been transferred.

3. Hang up.

To answer a UNA call:

1. Go offhook.

2. Dial

78

.

or

1. Directly pick up the UNA held trunk by pressing the dedicated trunk key.

«
...
368
369
370
371
372
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: D-Link Pages: 67

Brand: Samsung Pages: 68

Brand: Samsung Pages: 89

Brand: Samsung Pages: 72

Brand: Samsung Pages: 59

Brand: Samsung Pages: 42

Brand: Samsung Pages: 15

Brand: Jabra Pages: 7

Brand: Paradyne Pages: 17

Brand: Zazen Pages: 8

Opal Series 2006

Brand: Teledex Pages: 4

Hi-Phone Maestro

Brand: way2call Pages: 2

Brand: Amplicomms Pages: 51

Brand: dBTechnologies Pages: 49

Brand: Gigaset Pages: 112

Brand: ITT Pages: 12

Brand: Uniden Pages: 46

Brand: urmet domus Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands