Panasonic VB-44210G User Manual Download | Manualshive

Page: 286 / 394

background image

Chapter 6. SLT Features

Section 700 - Operation

6-30

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

2. Dial the desired extension number.

3. Upon hearing busy tone, press “5.”

Related Programming

• FF1 (System): Alert Tone for Busy Override & OHVA

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B 3.1 or higher)

• FF3 (Extension): Call Waiting/OHVA (Enable)

Considerations

• If Onhook Transfer is enabled, the held call is transferred as soon as the

extension sending the OHVA hangs up.

• You cannot receive a Call Waiting message during an OHVA.

• You cannot toggle back and forth between two calls while receiving an

OHVA.

• If you make an Offhook Voice Announcement to an SLT, the SLT user

and the other party

will hear the announcement.

Pooled Trunk Access

(All Versions)

Description

The DBS system is designed to accept from 8 to 64 outside lines. These lines
can be divided into seven Pooled Trunk groups. The groups are numbered 9
and 81-86.

Selecting a pooled trunk access number automatically selects a free trunk
from the group.

Operation

1. Lift the handset.

«
...
284
285
286
287
288
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Teac Pages: 3

Brand: Zazen Pages: 8

KX-TDA600 - Hybrid IP PBX Control Unit Max. 1008...

Brand: Panasonic Pages: 66

Brand: Panasonic Pages: 98

Brand: Barnstead|Thermolyne Pages: 56

Brand: Binatone Pages: 2

Brand: Ciro Pages: 2

Mainsboost Plus

Brand: Stuart Turner Pages: 28

Brand: JRC Pages: 110

Brand: VTech Pages: 37

Brand: Docomo Pages: 601

Brand: VTech Pages: 16

Brand: JBL Pages: 2

Brand: Vetus Pages: 16

Brand: Louroe Electronics Pages: 8

Brand: Excelltel Pages: 20

Brand: SpectraLink Pages: 38

Brand: VisIC Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands