Panasonic VB-44210G User Manual Download Page 244 | Manualshive

Page: 244 / 394

background image

Chapter 5. DSLT Features

Section 700 - Operation

5-26

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

routed to the extension defined in permanent call forwarding.

The following types of incoming trunk calls will follow permanent call
forward settings:

- Direct trunk calls (including DID/DNIS)

- Transferred trunk calls.

• The DND feature cannot be activated at an extension selected to receive

Call Forwarding.

Intercom Calling

(All Versions)

Descriptions

The DBS provides two methods of intercom calling: voice calling and tone
calling.

Voice Calling.

With voice calling, intercom calls are connected

immediately, without a ringing tone.

Tone Calling.

With tone calls, a ringing tone is sent to the called extension.

System programming determines whether the DBS uses voice or tone calling
as a default. If voice calling is the default, dialing a “1” after the extension
number will change the call to a tone call. If tone calling is the default, dialing
a “1” will result in a voice call.

Operation

To make a Voice Call:

1. Lift the handset.

2. Dial the extension number.

3. If the system default is tone calling, dial a “1.”

To make an Tone Call:

1. Lift the handset.

2. Dial the extension number.

«
...
242
243
244
245
246
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: Samsung Pages: 8

Brand: 3Com Pages: 128

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 36

SAPM71 - MINI HES W/CD PLAYER

Brand: Panasonic Pages: 12

Brand: Nady Systems Pages: 11

STARPLUS Triad-S 1

Brand: Vodavi Pages: 19

Brand: SKP Pro Audio Pages: 6

Brand: M-Life Pages: 16

Brand: RadonAway Pages: 22

Brand: Main Resource Pages: 5

Brand: eMoMo Pages: 2

AutoMotion Dome T2

Brand: MotoSAT Pages: 9

Brand: Southwestern Bell Pages: 6

Brand: Uniden Pages: 22

Brand: Jensen Pages: 41

Brand: HQ Power Pages: 29

Brand: Speaka Professional Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands