Panasonic VB-44210G User Manual Download Page 124 | Manualshive

Page: 124 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-8

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

• FF1 (System): Extension Class of Service Setting (CPC-AII and CPC-B

Version 3.1 or higher)

• FF3 (Extension): Extension Class of Service Assignment (CPC-AII and

CPC-B Version 3.1 or higher)

• FF3 (Extension): Busy Override Send

• FF3 (Extension): Busy Override Receive

• FF3 (Extension): Extension Page Group

Considerations

• You cannot break in on three-party conference calls.

• In CPC-A and CPC-B Versions 2.0 or lower, an Attendant Phone can

break into any call, independent of system programming.

Beginning with CPC-B Version 2.0, attendants can be prevented from
using busy override.

• The default for the override alert tone is “off.” If the override alert tone is

enabled, the tone will be sent to both parties when a call is overridden.

• In CPC-A and CPC-B Versions prior to 3.1, overridden extensions display

“CONF” when an override is performed. Beginning with CPC-B Version
3.1, “Overridden” does not appear on the display of an extension that has
been broken into.

Call Coverage Groups

(All Versions)

Description

Call coverage is designed for office workers who almost always want their
unanswered calls to be routed to the same secretary or secretaries.

If an extension in a Call Coverage Group is unable to receive a call, the call is
automatically routed to a designated phone within the group (the “covering”
phone).

Up to two extensions can be designated as covering phones.

«
...
122
123
124
125
126
...
»

Summary of Contents for VB-44210G











































































































































































































































































































































































































Reviews:

No comments

Related manuals for VB-44210G

Brand: ABRIVO Pages: 24

Brand: Galaxy Audio Pages: 2

Brand: CEECO Pages: 11

Brand: PURE Pages: 88

Brand: PHENYX PRO Pages: 12

Brand: Daewoo Pages: 33

Brand: Microlab Pages: 4

Brand: Dish TV Pages: 20

Brand: Tentel Pages: 10

Brand: Yealink Pages: 56

Brand: GE Pages: 32

Brand: GE Pages: 88

Brand: GE Pages: 15

Brand: GE Pages: 28

Brand: GE Pages: 20

Brand: GE Pages: 28

Brand: GE Pages: 38

Brand: GE Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands