background image

INSTALLATION  INSTRUCTIONS

Air Conditioner

This air conditioner uses the refrigerant R410A.

NOTE

  External diameter of service port R410A: 5/16" (7.94mm)

Model No.

Outdoor Units

Type Outdoor Unit Type

Nominal Capacity

MF2

3WAY VRF System

72

96

120

144

U-72MF2U9

U-96MF2U9

U-120MF2U9

U-144MF2U9

U-72MF2U94

U-96MF2U94

U-120MF2U94

U-144MF2U94

• To be connecting Indoor Unit

Indoor Units

Type Indoor Unit Type

Nominal Capacity

7

9

12

15

18

24

36

48

54

U2

4-Way Cassette 
36" × 36"

S-07MU2U6 S-09MU2U6 S-12MU2U6

S-24MU2U6 S-36MU2U6

Y2

4-Way Cassette 
24" × 24"

S-07MY2U6 S-09MY2U6 S-12MY2U6

S-18MY2U6

D1

1-Way Cassette

S-07MD1U6 S-09MD1U6 S-12MD1U6

F2

Concealed Duct 
- Medium Static

S-07MF2U6 S-09MF2U6 S-12MF2U6 S-15MF2U6 S-18MF2U6 S-24MF2U6 S-36MF2U6 S-48MF2U6 S-54MF2U6

M2

Concealed Duct
 - Low Static

S-07MM2U6 S-09MM2U6 S-12MM2U6 S-15MM2U6 S-18MM2U6

E1

Concealed Duct
 - High Static

S-36ME1U6 S-48ME1U6

T2

Ceiling

S-12MT2U6

S-18MT2U6 S-24MT2U6

K2

Wall Mounted

S-07MK2U6 S-09MK2U6 S-12MK2U6

S-18MK2U6 S-24MK2U6

P1

Floor Standing

S-07MP1U6 S-09MP1U6 S-12MP1U6 S-15MP1U6 S-18MP1U6 S-24MP1U6

R1

Concealed Floor 
Standing

S-07MR1U6 S-09MR1U6 S-12MR1U6 S-15MR1U6 S-18MR1U6 S-24MR1U6

Read through the Installation Instructions before you proceed with the installation.
In particular, you will need to read under the “IMPORTANT!” section at the top of the page.

85464369843023

CV6233323510

ACXF60-18571

01_302412_Eng.indd   1

2018/7/4   13:30:24

Summary of Contents for U-72MF2U94

































































Reviews: