ー 42 ー
When installing, pay special attention to this section.
1
4
Sufficient tension must be applied
to the end tension insulator.
2
Avoid tilting or twisting in the Tro-Reel unit.
3
The collector arm mount rod must
be properly mounted without
any twisting.
6
The Tro-Reel unit must be aligned with
the center of the collector arm.
5
Set the distance between the collector
arm mount rod and the sliding surface of
the Tro-Reel unit to 95mm.
(Central value of the collector arm permitted
movable range 95±20mm)
●
Ambient temperature during installation and coil spring tightening length
Critical six points on installation
Please read the following six precautions carefully before installing the Tro-Reel.
Please be sure to confirm if follow or not the precautions during the work and after installation.
Otherwise, fire, electric shock or damage due to falling of equipment may occur.
Coil spring length
If the Tro-Reel unit is tilted, the collector arm will separate from the wires.
Be sure to correct any tilting found during installation. (A spacer to prevent
tilting and twisting is also available.)
15
°
Inclination must be within 15
°
.
25m
m
25mm
L
a
A
a
Tro-Reel unit
Collector arm
95
20 or less
20 or less
95
±
20
Sliding surface of
the Tro-Reel unit
Collector arm
More than 115
Less than 75
Ambient temperature
10
℃
or lower
11-40
℃
Coil spring length
115mm
125mm
Be sure that arm swing is within
20mm, even during travel.
If tension is not sufficient, the collector arm may be derailed or fallen.
Set the length of "L" and "A"as well as
"
" and "a" to the same length.
Be sure to check for tilt in the
collector arm mount rod.
●
Do not modify the Tro-Reel HS in any way.
Otherwise, electric shock, fire or damage due to falling of equipment may occur.
●
Do not use where exposure occurs.
Otherwise, electric shock, fire or damage due to falling of equipment may occur.
●
Use at ambient temperature -10 ℃ ~ 40 ℃. If you use outside this temperature range, please contact Panasonic Corporation.
●
Install this product according to the construction rules in Electrical Equipment Technical Standards .
Especially for the primary side of power supply of the duct, use an adequate over-current breaker.
●
Installation must be carried out correctly according to this Installation/Operation Manual included with the products.
Improper installation may result in electric shock, fire or damage due to equipment falling.
■
Before assembling, be sure to read through this Operation / Installation Manual for correct assembly.
■
The work must be performed by a qualified engineer.
■
After setup
、
Please pass this Operation Manual / Installation Manual to the customer.
Installation of the High-Tro-Reel must be performed only by a licensed electrician. To prevent injury or accidents, always pay attention
to the following points.
Precautions on installation
●
Do not use this product for a damp place, a place where corrosive gas is generated or a place where cutting oil is directly splashed.
（
When corrosion resistance is required, please use the stainless steel products.
）
●
Do not install this product at the place where corrosion-resistance is absolutely necessary, for example, at ocean district,
cement factory or sewage treatment plant.
Electric shock, fire or damage due to equipment falling may occur.
●
In case of using outdoor or at a very damp indoor, use hanger with an insulator.
●
Position the opening of a unit facing downward or sideways. If installed with the opening facing upward, a unit may produce
sparks, causing fire, poor contact or separation of collector arms from wires.
●
When damage and crack occurred in the insulating sheath of the duct, please change the duct.
Otherwise sparking may occur, causing fire, poor contact, or derailing of the trolley, etc.
●
When mounting the duct to the hanger, stuff a duct into a hanger not to pinch a hand.
Observe may cause injury to your fingers.
●
When remove the duct from the joiners, pull it out while holding the tip of the duct. so that the duct may not jump out from Joyner.
Observe, damage to the ducts, may cause injury.
●
When filing the ends of the duct, use protective gear such as glasses.
Otherwise, your finger may be injured.
●
Be sure to remove burrs using file after cutting, drilling.
Observe may cause injury to your fingers.
●
Use products only within the specified rating and load capacity.
Violation of specified ranges may cause burning or fire.
●
Firmly fix this product to the material of construction and construct it.
Otherwise, fire or damage due to falling of equipment may occur.
●
Construct the material of construction that installs the product firmly.
Otherwise, damage due to falling of equipment may occur.
Warning
Caution
Tro-Reel Installation Manual
60A/150A/200A/300A(For indoor and outdoor use)
