Using the unit with a car audio
system
SL-SW891C comes with a car adaptor and car stereo
cassette adaptor.
Items to be purchased
(SL-SW895/SL-SW890)
For connection to the car audio system:
Car stereo cassette adaptor (SH-CDM10A)
For securing the unit and connecting the
power supply:
≥
Car adaptor (SH-CDC9)
≥
Car mounting kit (SH-CDF20)
Note
.
It may not be possible to use the unit with some types of
car stereo owing to restrictions imposed by the con-
struction of the car stereo cassette adaptor.
For further details, refer to the instructions of the part
concerned.
≥
The thinner and lighter construction makes the unit
less susceptible to vibration.
≥
An anti-skip mechanism prevents skipping caused
when play speed changes due to swinging of the unit.
≥
A recovery system immediately returns the laser pick-
up to its original position if it is knocked off the track by
a strong shock.
≥
The 40-second anti-skip memory fills in interruptions
caused by bumps and vibrations.
Press during play or stop mode.
The following indicator appears on the display panel.
Note
!
Wait until the jogger indicator appears before starting to
jog.
When bumps continue repeatedly
The message “SORRY” appears on the display and
sound is interrupted.
The jogger indicator can also flash or go out under
the following conditions:
≥
As the end of the last track approaches.
≥
As the end of a track approaches during random play, pro-
gram play, and 1 track repeat play.
≥
If the track in play or next track is extremely short.
To cancel the anti-skip function
Press [A.SKIP] again.
Note
!
≥
The anti-skip setting can be changed during play, but
this may cause a slight interruption in the sound be-
cause the disc’s rotational speed changes.
≥
During anti-skip operation, the disc rotates at a higher
rate than usual in collecting extra audio data. This
could result in a slight increase in disc rotation noise.
Listening to sound with the unit con-
nected to an audio system
The anti-skip function uses digital signal compression
technology. It is recommended that the anti-skip func-
tion be canceled if the unit is connected to a home
audio system.
Skipping
tracks
Searching
through tracks
To adjust the
volume
A.SKIP
A.SKIP
A.SKIP
5
Using the Unit with Optional Accessories
Using the unit with an audio system
Using a stereo connection cable (not included), you can
listen to CDs through your audio system.
≥
Connect the cable to the amplifier after turning off its
power.
≥
Do not connect the cable to the PHONO jacks on the
amplifier.
≥
Obtain the optional connecting cable if the amplifier
comes with mini-phone jacks.
≥
Adjust the volume level on the amplifier.
You can connect speakers, active or otherwise, with an
impedance of 1k
≠
or less to the headphone jack. Set
the unit’s volume between 5 and 8.
Note
.
Sound quality changes when S-XBS or VMSS
(SL-SW895 only) is selected, but volume is reduced
by approximately fifty percent.
L
R
OUT jack
Stereo connection cable (not included)
To CD or AUX
terminals
(White)
(Red)
Side panel of the unit
Amplifier
Connect the car stereo cassette adaptor
to the unit’s headphone jack.
(When doing this, keep the unit’s VOLUME
control at a setting between 5 and 8.)
RQT5963
Maintaining the
Lens
Open the lid and clean the lens as shown in the figure.
Use a cotton swab to gently wipe off any finger-prints.
Recommended product: Lens cleaner kit (SZZP1038C)
Lens
Lens
Air blower for
camera lens
Anti-Skip System
Using Stereo Headphones with Remote Control
SL-SW895 ONLY
To start play
To stop play
To turn off
the unit
The remote control can be operated regardless of the
HOLD mode of the unit.
Preparation: Release the remote control from the
HOLD mode.
∫
Operation confirmation tones
When an operation button is pressed, a confirmation
tone sounds. Refer to the parentheses in the illustra-
tion for the different types of confirmation tones.
How to use the remote control
Press once during off or stop mode.
Press once during play.
Press and hold during play or stop mode.
Press once during play.
Press and hold during play.
[VOL] on the remote control adjusts volume
only. To adjust the VMSS effect, use
[VOLUME] on the main unit.
VOL
HOLD
HOLD
VOL
HOLD
VOL
HOLD
VOL
HOLD
VOL
HOLD
VOL
HOLD
G
A.SKIP
After about
20 seconds
A.SKIP
Play/stop/off button
[
i
]
[
j
]
[VOL]
About
5 seconds later
The jogger indicator starts flashing.
(Beep)
(Beep...Beep)
(Beep...Bee...p)
Forward
(Beep
Beep)
Backward
(Beep Beep
Beep)
SL-SW895 ONLY
To prevent the disc from being scratched or
damaged
Remove built up dust from the felt pads.
Felt pads
