TROUBLESHOOTING
14
Symptom
Cause
Remedy
“ ” lights up on the
digital indicator (red)
Setting data error of
the product
•
Check the noise state.
•
In case the handy controller
SFB-HC
(optional) is applied,
reset the function.
• If the error is not cleared, con
-
tact our office.
“ ” blinks on the
digital indicator (red)
Emergency stop input
error
•
Wire the emergency stop input /
output wire correctly.
“ ” blinks on the
digital indicator (red)
The total number of
sensors / total number
of beam channels error
•
Check the total number of sen-
sors / total number of beam
channels.
“ ” blinks on the
digital indicator (red)
Reset input error
•
Wire the reset input / output wire
correctly.
“ ” blinks on the
digital indicator (red)
Safety output error
(Safety output circuit error)
•
Wire the safety output wire cor-
rectly.
“ ” blinks on the
digital indicator (red)
PNP / NPN setting
error
•
Change the setting after turning
the power OFF.
“ ” blinks on the
digital indicator (red)
Input voltage monitor
error
•
Check the supply voltage and
the voltage capacity.
“ ” blinks on the
digital indicator (red)
Safety output error
(Safety output short-circuited)
•
Wire the safety output wire cor-
rectly.
“ ” lights up on the
digital indicator (red)
The blanking func-
tion is valid.
•
The blanking function is valid.
(Normal operation)
“ ” lights up on the
digital indicator (red)
Light curtain commu-
nication error
•
Check if the light curtain is con-
nected correctly.
•
Check the operation of the con-
nected light curtain.
“ ” blinks on the
digital indicator (red)
Safety output circuit
error
•
Check the noise state.
“ ” blinks on the
digital indicator (red)
Effect by noise, power, etc.
or internal circuit failure
•
Check the noise state.
“ ” blinks on the
digital indicator (red)
Internal error of the
product
•
Check the noise state.
• Check the wiring, supply voltage
and voltage capacity.
•
If the product does not work cor-
rectly, contact our office.
The test input indicator
(yellow) lights up
The product is in test
state.
•
Wire the test input wire correctly.
The test input indicator
(yellow) blinks
The handy controller
SFB-HC
has been
connected.
•
Remove the handy controller
SFB-HC
.
Only the power indicator
(green) and the auxiliary
output 1, 2 and 3 indica
-
tors (orange) light up.
All of the safety outputs
1, 2 and 3 are OFF.
T h e p r o d u c t i s i n
emergency stop state.
•
Wire the emergency stop input /
output terminals between S11 and
S12, and S21 and S22 correctly.
•
Check if the emergency stop
switch has been “pressed.”
The interlock indicator
(yellow) lights up.
R e s e t c a n n o t b e
canceled.
•
Wire the reset input / output wire
correctly.
•
Change the relay having appro-
priate response time.
•
Replace the relay.
DIMENSIONS (Unit: mm)
16
10
130
67.3
35
4
54.1
40
6.5
80
(99)
25
34.1
13
31.1
11
23
18 18.4
38.4
46
Suitable for 35mm width DIN rail
Emitter side
connector
Receiver
side
connector
MAINTENANCE
15
●
Be sure to do maintenance before use and 6 month periodic main-
tenance. Refer included instruction manual of light curtain for the
inspection items.
● In case replacing this device to new this device, be sure special
technician to exchange it. And do daily maintenance and periodic
maintenance.
INTENDED PRODUCTS FOR CE MARKING
17
●
The model listed under “
SPECIFICATIONS
” comes with
CE Marking.
As for all other models, please contact our office.
CE MARKING DECLARATION OF CONFORMITY
18
Itemized Essentials of EU Declaration of Conformity
Manufacturer’s Name:
Panasonic Industrial Devices SUNX Co., Ltd.
Manufacturer’s Address:
2431-1, Ushiyama-cho, Kasugai, Aichi
486-0901, Japan
EU Representative’s Name:
Panasonic Marketing Europe GmbH Panasonic Testing Center
EU Representative’s Address:
Winsbergring 15, 22525 Hamburg, Germany
Product:
Exclusive Control Unit for Light Curtain
Model Name:
SF-C10
Series
Trade Name:
Panasonic
Application of Council Directive:
-
2006/42/EC Machinery Directive
-
2004/108/EC EMC Directive (Valid until April 19, 2016)
-
2014/30/EU EMC Directive (Valid from April 20, 2016)
-
2011/65/EU RoHS Directive
Harmonized standards:
-
EN 61496-1: 2013
-
EN ISO 13849-1: 2008
-
EN 55011: 2009+A1: 2010
-
EN 50581: 2012
Type Examination:
Certified by TÜV SÜD Product Service GmbH
Ridlerstrasse 65 80339 München Germany
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: [email protected]
