Panasonic Section 700 User Manual Download | Manualshive

Page: 158 / 394

background image

Chapter 4. Key Telephone Features

Section 700 - Operation

4-42

DBS Manual - Revised April 2000

DBS-2.3/9.2-700

Delayed Ringing

(CPC-AII and CPC 2.0 and higher)

Description

Delayed ringing causes a call that is unanswered at a primary extension to
ring at a secondary extension.

CO delayed ringing causes an incoming outside call to ring at a designated
extension or extensions if it is not answered within a certain period of time.
CO delayed ringing is also available for hunt group pilot numbers.

Extension delayed ringing causes any type of call, outside or intercom, to ring
at a designated extension or extensions if it is not answered within a certain
period of time. The phones receiving the delayed call must have a DSS/BLF
key assigned to the extension originally intended to receive the call.

Considerations

• In CPC-B Versions prior to 3.1, timing for CO and extension delayed

ringing was controlled by the Call Forward - No Answer Timer.

• In CPC-AII and CPC-B Versions 3.1 and higher, the following timers have

been implemented:

- The Central Office Delayed Ring Timer controls delayed ringing for

outside calls.

- The Extension Delayed Ring Timer controls delayed ringing for

extension calls.

Dial “0” for Attendant

(All Versions)

Description

The Attendant can be called from any extension by simply pressing “0.”

If multiple attendants are assigned, a dial “0” call goes to the first Attendant
first. If the first attendant is busy, the call goes to the second Attendant. The
call will continue to transfer to the next attendant in the attendant group if
necessary.

«
...
156
157
158
159
160
...
»

Summary of Contents for Section 700











































































































































































































































































































































































































Reviews:

No comments

Related manuals for Section 700

Brand: i-onik Pages: 5

Brand: Aquos Phone Pages: 88

Brand: Serioux Pages: 24

Brand: Slican Pages: 50

Brand: Fortinet Pages: 28

Brand: Allview Pages: 30

Brand: Dartel Pages: 43

Brand: Ericsson Pages: 63

Brand: Pantech Pages: 97

Brand: PCD Pages: 73

Brand: Alcatel Pages: 28

Brand: Yarvik Pages: 515

Brand: Digital2 Pages: 14

Brand: Samsung Pages: 113

Brand: Samsung Pages: 201

Brand: Samsung Pages: 104

Brand: IPRO Pages: 35

Brand: i-mobile Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands