RQTX1061
ENGLISH
9
9
Specifications
g
AMPLIFIER SECTION
RMS Output Power Stereo mode
Front Ch (both ch driven)
5 W per channel (6
Ω
), 1 kHz, 10 % THD
PMPO output power
95 W
Phone jack
Terminal
Stereo, 3.5 mm jack
Output level (CD, 1 kHz, -20 dB)
max. 0.385 mW + 0.385 mW, 32
Ω
Aux (Rear)
Sensitivity
Normal level
504 mV, 12.4 k
Ω
High level
100 mV, 12.4 k
Ω
Terminal
Stereo, 3.5 mm jack
g
TUNER SECTION
Preset Memory
FM 30 stations
AM 15 stations
Frequency Modulation (FM)
Frequency range
87.50 MHz to 108.00 MHz (50 kHz step)
Antenna terminals
75
Ω
(unbalanced)
Amplitude Modulation (AM)
Frequency range
522 kHz to 1629 kHz (9 kHz step)
520 kHz to 1630 kHz (10 kHz step)
g
DISC SECTION
Disc played [8 cm or 12 cm]
(1) CD-Audio (CD-DA)
(2) CD-R/RW (CD-DA, MP3)
(3) MP3*
* MPEG-1 Layer 3, MPEG-2 Layer 3
Pick up
Wavelength
785 nm
Laser power
CLASS 1
Audio Output (Disc)
Number of channels
FL, FR, 2 channel
g
SPEAKER SECTION
Type
1 way, 1 speaker system (Bass reflex)
Speaker unit(s)
Full range
8 cm Cone type
Impedance
6
Ω
Output sound pressure
83 dB/W (1.0 m)
Frequency range
60 Hz to 25 kHz (-16 dB)
90 Hz to 22 kHz (-10 dB)
g
GENERAL
Power supply
AC 110 V to 240 V, 50/60 Hz
Power consumption
18 W
Dimensions (W x H x D)
384 mm x 214 mm x 112 mm
(D = 69 mm minimum)
(D = 147 mm tray open)
Mass
Approx. 2.1 k
g
Operating temperature range
0 °C to +35 °C
Operating humidity range
35 % to 80 % RH (no condensation)
Power consumption in standby mode:
0.3 W (approx.)
Specifications are subject to change without notice.
Total harmonic distortion is measured by the digital spectrum
analyser.
•
•
Placement
Safety precautions
Voltage
AC mains lead protection
Foreign matter
Service
Set the unit up on an even surface away from direct sunlight, high
temperatures, high humidity, and excessive vibration. These conditions
can damage the cabinet and other components, thereby shortening the
unit’s service life.
Do not place heavy items on the unit.
Do not use high voltage power sources. This can overload the unit and
cause a fire.
Do not use a DC power source. Check the source carefully when
setting the unit up on a ship or other place where DC is used.
Ensure the AC mains lead is connected correctly and not damaged.
Poor connection and lead damage can cause fire or electric shock. Do
not pull, bend, or place heavy items on the lead.
Grasp the plug firmly when unplugging the lead. Pulling the AC mains
lead can cause electric shock.
Do not handle the plug with wet hands. This can cause electric shock.
Do not let metal objects fall inside the unit. This can cause electric
shock or malfunction.
Do not let liquids get into the unit. This can cause electric shock or
malfunction. If this occurs, immediately disconnect the unit from the AC
mains supply and contact your dealer.
Do not spray insecticides onto or into the unit. They contain flammable
gases which can ignite if sprayed into the unit.
Do not attempt to repair this unit by yourself. If sound is interrupted,
indicators fail to light, smoke appears, or any other problem that is not
covered in these instructions occurs, disconnect the AC mains lead and
contact your dealer or an authorized service centre. Electric shock or
damage to the unit can occur if the unit is repaired, disassembled or
reconstructed by unqualified persons.
Extend operating life by disconnecting the unit from the AC mains if it
is not to be used for a long time.
- If you see this symbol -
Information on Disposal in other Countries outside the
European Union
This symbol is only valid in the European Union.
If you wish to discard this product, please contact
your local authorities or dealer and ask for the
correct method of disposal.
Memory reset (Initialization)
When the following situations occur, reset the memory:
There is no response when buttons are pressed.
You want to clear and reset the memory contents.
To reset memory
Disconnect the AC mains lead.
(Wait for at least 3 minutes before
proceeding to step 2.)
While pressing and holding down [
8
] on the main unit,
reconnect the AC mains lead.
“--------” appears on the display.
Release [
8
].
All the settings are returned to the factory preset. You will need to
reset the memory items.
•
•
Maintenance
g
Pull out the power plug from the outlet for maintenance
beforehand and then wipe it using a soft and dried cloth.
When dirt is heavy, wring the cloth moistened in water tightly to wipe
the dirt, and then wipe it with a dried cloth.
Do not use solvents such as benzine, thinner, alcohol and detergent,
which may deform the coating of the outer case.
When using a chemical cloth, follow the precautions.
g
Care on the CD lens
Clean the lens regularly to prevent malfunctions. Use a blower to
remove dust and a cotton swab if it is extremely dirty.
Do not use the lens cleaner of the CD type.
•
•
•
•
•
