12
TQ
BM
087
3
Others
Auto off
This system automatically turns off when you do not use it
for approximately 20 minutes.
1
Press [SETUP] repeatedly to select “AUTO OFF”.
2
Press [
R
,
T
] to select “ON” and then press [OK].
To cancel, select “OFF”.
Note:
This function does not work when you are in radio source or
when a Bluetooth
®
device is connected.
Bluetooth
®
standby
This function automatically turns on the system when you
establish a Bluetooth
®
connection from a paired device.
1
Press [SETUP] repeatedly to select
“BLUETOOTH STANDBY”.
2
Press [
R
,
T
] to select “ON” and then press [OK].
To cancel, select “OFF”.
Note:
Some devices may take longer to respond. If you are
connected to a Bluetooth
®
device before turning off the
system, wait for a minimum of 5 seconds before connecting to
this system from your Bluetooth
®
device again.
Software updates
Occasionally, Panasonic may release updated software
for this system that may add or improve the way a feature
operates. These updates are available free of charge.
For more details, refer to the following website.
https://panasonic.jp/support/global/cs/
(This site is in English only.)
█
Checking the software version
1
Press [SETUP] repeatedly to select “SW VER.”
and then press [OK].
The software version is shown.
2
Press [OK] again to exit.
Troubleshooting
Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult your
dealer for instructions.
When requesting service, make sure to send both the
main unit and the remote control to the service center.
█
Common problems
The unit does not work.
•
The safety device has been activated. Do the following:
1.
Press [
1
] on the main unit to turn the unit to standby
mode. If the unit does not turn to standby mode,
disconnect the AC power supply cord and connect it
again.
2.
Press [
1
] again to turn on the unit. If the problem
persists, consult your dealer.
No operations can be done with the remote control.
•
Examine that the battery is installed correctly.
Sound is distorted or no sound.
•
Adjust the volume of the system.
•
Turn off the system, determine and correct the cause, and
then turn on again. It can be caused by straining of the
speakers through excessive volume or power, and when
using the system in a hot environment.
A humming sound can be heard during playback.
•
An AC power supply cord or fluorescent light is near the
cables. Keep other appliances and cords away from the
cables of this system.
█
Disc
Display not shown correctly.
Playback does not start.
•
You have not put in the disc correctly. Put it in correctly.
•
Disc is dirty. Clean the disc.
•
Replace the disc if it is scratched, warped, or non-standard.
•
There is condensation. Let the system dry for 1 to 2 hours.
The total number of tracks shown is incorrect.
The disc cannot be read.
Distorted sound is heard.
•
You put in a disc that the system cannot play. Change to a
playable disc.
•
You put in a disc that has not been finalized.
█
USB
The USB device or the contents in it cannot be read.
•
The format of the USB device or the contents in it are not
compatible with the system.
•
USB devices with storage capacity of more than 32 GB
cannot work.
•
USB devices may not be recognized when connected to this
system with a USB extension cable or USB hub.
Slow operation of the USB device.
•
Large content size or large memory USB device takes
longer time to read.
The elapsed time shown is different from the actual play
time.
•
Transfer the data to another USB device or backup the data
and reformat the USB device.
PM700PP_TQBM0873_en.fm Page 12 Friday, March 17, 2023 4:34 PM
