Panasonic SC-HG1-C User Manual Download Page 24

Page: 24 / 128

Installation and Settings

WUME-SCHG1C-4

3-2

3-1 Steps prior to operation

The steps that are required prior to operation are indicated below.

Check column

Page

“3-2-2 Communication unit

settings”

Mode settings

Follow the setting procedures to set the product's

communication method and number of occupied sta-

tions.

Controller settings

Configure controller settings.

Configure threshold and other settings by program

ming or direct setting on the controller.

For direct setting on a controller, refer to the manual

for the controller.

“2 System Configuration”

“3-3-1 Mounting”

“3-3-2 Connection”

Unit mounting

Mount the product and controllers on a DIN rail ac-

cording to the system configuration, and connect.

“3-2-2 Communication unit

settings”

Station number and communication speed settings

Follow the setting procedures to set the product's

station number and communication speed.

“3-2-1 CC-Link communication set-

tings”

“4 CC-LINK Network Communica-

tion”

“4-10-1 HG-S series command list”

Programming

Create a program for control of each controller con-

nected to the product from the master station.
*1: You can use CSP+ (CC-Link System Profile) to

easily configure CC-Link communication settings.

Connect power supply

Connect the power supply of the master controller.

“3-3-3 Pin layout”

“3-3-4 Host communication cable

connection”

“3-3-5 Procedure for connecting the

CC-Link connector”

“3-3-6 Attachment and removal of

termination resistor”

Wiring

Connect the communication cable and a termination

resistor (if needed) to the CC-Link connector, and at-

tach to the product.

Summary of Contents for SC-HG1-C

































































































































Search results

Summary of Contents for SC-HG1-C

Reviews:

Panasonic SC-HG1-C, User Manual, Page: 24 / 128

Search results

Summary of Contents for SC-HG1-C

Reviews: