51
RQT9508
Messages
The following messages or service numbers appear on the TV or unit’s display when something unusual is detected during startup and use.
On the TV
Page
Cannot play.
≥
You inserted an incompatible disc (Discs recorded in PAL video, etc.).
42, 43
Cannot display on this unit.
≥
You tried to play a non-compatible image.
43, 44
No disc is inserted.
≥
The disc may be upside down.
—
$
This operation is not
available.
≥
Some operations are prohibited by the unit or disc. For example;
–
[BD-V]
:
During play back, reverse slow-motion or reverse frame-by-frame is not possible.
—
$
This operation is prohibited
by this disc.
≥
Depending on the disc, you may not be able to perform search or skip when film previews
and warning screens are being played back.
—
Cannot connect.
Please check the connection of
the LAN cable.
≥
When a hub is used but its Link lamp does not light up, check the cable connection, LAN
terminal connection, cable itself (a cross cable may be used by mistake), etc.
14
IP address is not set.
≥
The “IP Address” in “IP Address/DNS Settings” is “---. ---. ---. ---”. Set the “IP Address”,
“Subnet Mask”, and “Default Gateway”. (Select the automatic address acquisition if
necessary.)
33
Cannot obtain IP address using
DHCP.
Please check the connection or
router settings.
≥
If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– Check whether or not the hub’s Link lamp lights up. If it does not light up, then check the
cable connection, LAN terminal connection, cable itself (a cross cable may be used by
mistake), etc.
≥
If the above conditions are OK, then the router may not operate in DHCP mode. Check the
router settings and operation. You may reset the router to restore it to normal.
14
14
This IP address is already in
use.
Please check the IP address
setting.
≥
This unit’s IP address is used by another device. Check the IP addresses of this unit,
personal computers, and routers, etc. If necessary, reconfigure them to avoid IP
addresses from being duplicated.
—
Unable to perform Connection
Test.
Please try again.
≥
Turn the unit off. Remove the power cord and reconnect it and try again. If the same
symptom persists, then consult your dealer.
—
IP address not set correctly.
Connection Test was
unsuccessful. No reply
from host.
Please check the connection or
router settings.
≥
If you use a hub, then check the connection between the hub and the router.
– Use the UPLINK port of the hub to connect to a router.
– If the hub’s Link lamp does not light up, then check the cable connection, LAN terminal
connection, cable itself (a cross cable may be used by mistake), etc.
≥
Check the “IP Address”, “Subnet Mask”, and “Default Gateway” in the “IP Address/DNS
Settings”.
≥
If the MAC address information is required, then press [SETUP] to display the “Network”
menu.
14
33
33
Network connection refused.
Please confirm Setup “BD-Live
Internet Access.”
≥
When you set “BD-Live Internet Access” to “Allow ( Limited )” and play BD-Live contents
which do not have a content owner certificate, the Internet access of the content is not
allowed. If you allow the content to connect to Internet, set “BD-Live Internet Access” to
“Allow ( ALL )”.
37
Unable to check for latest
firmware version.
Please try again later.
≥
The firmware download server is currently unavailable. Please try again later.
—
High Clarity Sound is effective.
Analog video output is turned
off when
playback starts.
≥
“High Clarity Sound” in setup menu is set to “Enable”, and “High Clarity Sound” in
on-screen menu is set to “On”.
36, 38
No Video
≥
Depending on the connected iPod, video menu may not be available on the TV. Select the
iPod menu (iPod LCD) mode and operate video playback from your iPod menu.
31
On the unit’s display
F99
≥
The unit fails to operate properly. Press [POWER
Í
/I] on the main unit to switch the unit to
standby for 3 seconds. Now press [POWER
Í
/I] on the main unit again to turn the unit on.
—
HDMI ONLY
≥
Some BD-Video discs can only be output with HDMI.
—
NET
≥
Displays while VIERA CAST is starting up.
—
No PLAY
≥
There is a viewing restriction on a BD-Video or DVD-Video.
37
No READ
≥
The media is dirty or badly scratched. The unit cannot play.
—
PLEASE WAIT
≥
The unit is carrying out internal process.This is not a malfunction. You cannot operate the
unit while “PLEASE WAIT” is displayed.
≥
When connected to a TV (VIERA) with HDAVI Control 4, and power supply is turned off by
the “Auto power stand-by” function on the TV side.
—
—
SET
(“
” stands for a number.)
≥
The remote control and main unit are using different codes. Change the code on the
remote control.
Press and hold [OK] and the indicated number button at the same
time for more than 5 seconds.
50
UNFORMAT
≥
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an R, +R DL or
DVD-RW (DVD-Video format).
—
UNSUPPORT
≥
You have inserted a media the unit cannot play.
42, 43
Reference
BT300.book 51 ページ ２００９年６月１２日 金曜日 午後１２時１３分
