Panasonic S-18MK2U6 Installation Instructions Manual Download Page 16 | Manualshive

Page: 16 / 28

background image

16

CAUTION

(1) When linking outdoor units in a network, disconnect the terminal extended from the short plug (on the outdoor main

control PCB) from all outdoor units except any one of the outdoor units.
(When shipping: In shorted condition.)
For a system without link (no connection wiring between outdoor units), do not remove the short plug.

(2) Do not install the inter-unit control wiring in a way that forms a loop. (Fig. 4-3)

Outdoor unit

Outdoor unit

Outdoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Prohibited

Prohibited

Indoor unit

Fig. 4-3

(3) Do not install the inter-unit control wiring such as star branch wiring. Star branch wiring causes misaddress setting.

(Fig. 4-4)

Fig. 4-4

(4) If branching the inter-unit control wiring, the number of branch points should be 16 or fewer.

Central Controller

Outdoor unit

Outdoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Outdoor unit

: Branch point

More than 6.6 ft. (2m) required

Fig. 4-5

Outdoor unit

Indoor unit

Indoor unit

Indoor unit

Indoor unit

NO

Branch point

00̲271654̲Eng.indb 16

00̲271654̲Eng.indb 16

2015/09/04 11:57:35

2015/09/04 11:57:35

«
...
14
15
16
17
18
...
»

Summary of Contents for S-18MK2U6





























Reviews:

No comments

Related manuals for S-18MK2U6

Brand: Kahn Pages: 8

Brand: Daikin Pages: 19

Brand: INVENTOR Pages: 106

Brand: Trane Pages: 52

Super Multi NX FFQ25B8V1B

Brand: Daikin Pages: 501

Brand: Champion Pages: 12

Brand: Kelvinator Pages: 16

Brand: Toyotomi Pages: 24

Brand: Graymills Pages: 4

Brand: Trotec Pages: 23

Versati III GRS-CQ10Pd/NhH-M

Brand: Gree Pages: 58

Mr. Slim PEA-A12AA4

Brand: Mitsubishi Pages: 28

Brand: b-mola Pages: 8

Brand: Daikin Pages: 8

Brand: Russell Hobbs Pages: 32

Brand: Haier Pages: 22

Brand: Haier Pages: 26

Brand: Haier Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands