Panasonic PT47WXD63G - 47" PROJECTION TV Service Manual Download Page 41 | Manualshive

Page: 41 / 197

background image

2. Select TIMER icon and set SLEEP time for 30 Min.

3. Press “OK” then VOL up to exit menus.

4. Tune to the Channel 124.

5. Adjust VOLUME to minimum (0).

6. Press VOL (decrease) on receiver. Red “CHK” appears in upper

corner.

To toggle between aging and service modes:
While the “CHK” is displayed on the left top corner of the CRT, pressing “OK” and “VOL” UP on
the TV simultaneously will toggle between the modes. Red “CHK” for service modeand yellow
“CHK” for aging.

7. Press POWER on the remote control to display the service

adjustment modes menu, select adjustment by pressing the VOL
right/left buttons and CH up/down buttons on the remote and OK to
enter the adjustment.

Service mode menu

15.2. Exiting the service mode:

This PTV goes out from service mode when it is unplugged or turned OFF. To exit the service
mode, turn the TV OFF or unplug the PTV from AC.

Other method
Press  OK and POWER on the receiver simultaneously for at  least 2 seconds.The receiver
momentarily  performs  a self-check, tuned in channel 3 with a preset level of sound. To
completely  make an entire reset of the PTV unplug AC cord from AC outletand plug it back in,
then turn PTV power ON.Any programmed channels, channels  caption data and some others
user defined settings  will be erased when performing this  reset.

41

«
...
39
40
41
42
43
...
»

Summary of Contents for PT47WXD63G - 47" PROJECTION TV






































































































































































































Reviews:

No comments

Related manuals for PT47WXD63G - 47" PROJECTION TV

Brand: IFM Pages: 7

Brand: Wacom Pages: 113

Brand: BIOS Diagnostics Pages: 20

Brand: ViewSonic Pages: 115

Brand: Angelcare Pages: 8

Brand: Newskill Pages: 9

Brand: laerdal Pages: 40

Brand: RF-Link Pages: 2

PRTD-090T-5A-N4F

Brand: Icop Pages: 32

GALAXY GT6 Series

Brand: Daktronics Pages: 2

Brand: BenQ Pages: 37

Brand: Masterclock Pages: 39

SyncMaster P50FP

Brand: Samsung Pages: 105

SyncMaster P1980ER

Brand: Samsung Pages: 47

SyncMaster PX2370

Brand: Samsung Pages: 47

SyncMaster 320P

Brand: Samsung Pages: 70

SyncMaster 320P

Brand: Samsung Pages: 69

SyncMaster 650FP

Brand: Samsung Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands