Panasonic PT-LC56E, Operating Instructions Manual

Page: 22 / 32

E
NGLISH
-43
Adjustments
and
settings
42-E
NGLISH
Use the
F
and
G
buttons on the
projector or remote control unit to
select an item, then press the
I
or
H buttons to change the setting.
OSD
ON
The current input name is displayed
in the top-right corner of the screen
when the input signal is changed.
OFF
Use this setting when you do not
want the current input name to be
displayed.
AUTO SIGNAL
This should normally be set to ON.
ON
AUTO SETUP will be carried out
automatically when the input signal
is changed.
OFF
AUTO SETUP will not function
when the input signal is changed.
AUTO KEYSTN
This should normally be set to ON.
ON
During automatic setup, the angle of
tilt of the projector is detected and
keystone distortion is corrected
automatically.
OFF
Use this setting when you do not
want automatic keystone correction
to be carried out during automatic
setup, such as when the screen
itself is at an angle.
AUTO RGB IN
This should normally be set to ON.
ON
During automatic setup, the
projector selects whichever one of
the RGB1 IN or RGB2 IN
connectors has a signal being input,
and uses that signal for projection.
(If a picture is being projected, the
signal source is not automatically
changed.)
OFF
Use this setting when you do not
want the signal source to be
changed automatically during
automatic setup.
RGB2 SELECT
This setting is used to select the
function of the RGB2 IN/RGB1 OUT
connector.
R G B 2 S E L E C T I N P U T
[
O U T P U T
RGB/YP
B
P
R
This should normally be set to
AUTO. RGB or YP
B
P
R
is selected
automatically depending on the
synchronising signal status.
When HDTV, 525p (480p), 525i
(480i), 625i, 750p, and some
VGA480 signals are being
input, select “RGB” or “YP
B
P
R
” in
accordance with the input signal.
VGA60/525P
When a VGA60 or 525p RGB signal
is being input, select the signal in
accordance with the input signal.
SXGA MODE
This setting is only for an SXGA
signal.
SXGA
Select this item normally.
SXGA+
When the projected image is
contracted vertically, select this
item.
BLACKBOARD
(PT-LC80E only)
Set to “ON” when PICTURE MODE
is set to BLACK-BD. (Refer to page
35.)
BACK COLOR
This sets the colour which is
projected onto the screen when no
signal is being input to the projector.
FRONT/REAR
This setting should be changed in
accordance with the projector
setting-up method.
Set to “FRONT” when using a
normal reflective screen with the
projector positioned in front of the
screen, and set to “REAR” when
using a translucent screen with the
projector positioned behind the
screen.
DESK/CEILING
This setting should be changed in
accordance with the projector
setting-up method.
Set to “DESK” when setting up the
projector on a desk or similar, and
set to “CEILING” when suspending
the projector from the ceiling using
the ceiling bracket which is sold
separately.
FAN CONTROL
Set FAN CONTROL to “HIGH”,
when using this projector at high
elevations (above 1400 m) only.
LAMP POWER
This setting changes the lamp
brightness. When set to “LOW”, the
R G B / Y P
B
P
R
A U T O
[
R G B
[
Y P
B
P
R
V G A 6 0 / 5 2 5 P 5 2 5 P
[
V G A 6 0
B A C K C O L O R B L U E
[
B L A C K
F R O N T / R E A R F R O N T
[
R E A R
D E S K / C E I L I N G D E S K
[
C E I L I N G
L A M P P O W E R H I G H
[
L O W
S X G A M O D E S X G A
[
S X G A +
F A N C O N T R O L S T A N D A R D
[
H I G H
Option settings
O P T I O N 1
O S D O N
A U T O S I G N A L O N
A U T O K E Y S T N O N
A U T O R G B I N O N
R G B 2 S E L E C T I N P U T
R G B / Y P
B
P
R
A U T O
V G A 6 0 / 5 2 5 P 5 2 5 P
S X G A M O D E S X G A
B L A C K B O A R D O F F
S E L E C T A D J R E T R N
O P T I O N 2
B A C K C O L O R B L U E
F R O N T / R E A R F R O N T
D E S K / C E I L I N G D E S K
F A N C O N T R O L S T A N D A R D
L A M P P O W E R H I G H
L A M P R U N T I M E 1 0 0 H
F U N C 1 I N D E X
C O N T R O L K E Y O N
A U T O P O W . O F F D I S A B L E
S E L E C T A D J R E T R N